Jump to content
SAU Community

Recommended Posts

Hi,

Have the following items for sale;

324mm Brake Upgrade Kit

S14 Calipers and rotors drilled to 4 stud

R32 GTR Front Calipers

Yokohama Advan 235/45/17 Semi's

RE 55's 235/45/17 semi's

17 x 7.5 + 35 ALT Wheels

16x7 & 16x8 Blitz Wheels

Whiteline Front Strut Brace

Info below.

All items located in Sydney.

All prices are near offer! Need these gone!

Can be contacted by PM or 0403 434 495.

BRAKES

Selling all these brake items as I am looking to upgrade to an AP Racing Kit.

1. 324mm Big Brake Upgrade Kit for S14/S15/R32/R33/Z32 300ZX

Price: $480 ono

This kit can be used with your standard calipers. You bolt this kit on to use a 324mm GTR Brembo sized rotor which not only looks better but provides better braking ability. This was only used for approximately 5000km. I have not used it I have only fitted it to make sure it all fits up which it does.

I bought the kit to use with the R32 GTR calipers but they did not fit.

Kit contains;

324mm GTR sized DBA 4000 rotors

Brackets to mount the caliper in the new position

All bolts, nuts and washers to fit

Ferodo Formula Pads (Standard sized pads can also be used and are recommended by some)

This is the same kit as this on ebay which sells for $900

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...em=130094159891

IMG_3743.jpg

2. S14 Brake Calipers with S14 rotors that have been redrilled to 4 stud.

Price: $350 ono

S14 calipers in reasonably good condition with rotors. Can use these on S13/180SX without having to do a 5 stud conversion. These were on my car for 25000km and did quite a few track days. They stop really well and I had no problems whatsoever with them. The rotors were machined approx 3000km's ago. The rust is from water that fell on the rotor - this will come straight off after a light drive.

Will throw in Lucas TRW pads that have only done one track day ie 400km's.

Caliper pics above ^^^^

IMG_3819.jpg

3. R32 GTR Front Brake Calipers

Price: $280 ono

R32 GTR front calipers that I bought but never used. Was told they came off a 1992 R32 with 70,000km's. Bought off a respected member on here. I have painted them with the intent to put onto the car.

These do not fit with the 324mm brake upgrade kit (I was told they did ) which is why I bought them.

IMG_3801.jpg

SEMI SLICKS

1. Yokohama Advan AO48 235/45/17 Full Set of 4

Price: $300 ono

OK condition, good for a few track days. Bought these a little while ago but never got round to fitting them up. Have been stored in my garage.

IMG_3802.jpg

IMG_3804.jpg

IMG_3806.jpg

2. Bridgestone RE55's 235/45/17 Full Set of 4

Price: See below

Still have a few track days in them maybe more. I changed to 5 stud so could not use the wheels they were on. They are still on the wheels.

IMG_3809.jpg

IMG_3816.jpg

WHEELS

1. 17x7.5 + 35 all 4 ALT Wheels

Price: $600 ono with the RE55's semi's

Some gutter rash, but they made great track wheels and or drift wheels. Have the Bridgestones semi on them.

Would prefer to sell together with the RE55's but can separate at buyers expense.

IMG_3814.jpg

IMG_3812.jpg

Worst of the gutter rash

IMG_3815.jpg

2. Blitz Rims 16 x 7 and 16 x 8 I think +35 and + 38

Price: $250 for all 4

One of the 16 x 8 rims has a chunk missing on the inside of the rim (probably 5-8cm wide) that would need to be repaired. Not knowing this I drove on the rim from Wakefield Park to Sydney and it drove fine, no wobble or sign of a buckle nor leaking tyre.

No pics but they look like these; not in as good nick though!

http://www.japanautoswrec.info/DSCF0861.JPG

STRUT BRACE

1. Whiteline Adjustable Front Strut Brace

Price: $100 ono

Don't need this as I have a Cusco Brace. Bought off a NS.com member. Came off a 180SX SR20DET.

IMG_3807.jpg

IMG_3808.jpg

Interested in brake upgrade kit. Could you check the postage price to 2830?

Have posted rotors previously using Australia post.

I would say it would be absolute maximum $50 using registered post.

Thanks to all those interested.

Semi Slicks and ALT Wheels are Sold.

Strut Brace is Sold.

324mm Brake Upgrade Kit - Offer made awaiting deposit to be paid.

All other items still available.

Thanks.

324mm Brake Upgrade Kit Sold.

Items remaining are;

S14 calipers with rotors (4 and 5 stud)

R32 GTR calipers

Blitz 16 inch wheels with Kuhmo Semi Slicks (pretty worn) Will post pics tonight or tomorrow

Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...