Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Nothing wrong with Nissan coils... R32/R33. Hell i used stock RB25 coils for 370rwkw @ 24psi. I needed a HKS box to go further, that was my only issue.

Splitfires/Nissan - all the same shit anyhow really. Only difference is the price.

I highly doubt the HKS car would be changing coil packs each run though.

Seen many a car here make 380-400rwkw on nissan/splitfires without a HKS DLI!

Once you get into the 400rwkw+ region however the little HKS 'black box' is another key ingredient required... I bet the HKS drag car has a HKS black box :D

Only thing is does the black box decrease the life of the coils? That is something that there seems to be zero information about.

c'mon! don't tease a bloke. I need facts dammit. or at least some well worded lies?! give me somethng.

Can i try to start? :D

The plugs were originally 1.1, and gapped down by hand... in the process the head was damaged on one/two of the plugs!

HKS quite possibly change their coilpacks as often as they do plugs.. which is after 7 seconds.. i have no doubt that the standard coilpacks are capable, when new.. but i think id rather cough up $600 for splitfires than $1500 for a new set of stockies.

i recently back to back tested stocko's vs splitfires, stockso were f**k knows how many genuine km's old out of an r32gtr engine package, punishing both sets of coils on the dyno stock where better, not buy all that much but considering the condition of the stocko's and the splitfires(barely10-15000km's old) i'll never use anything but stock coils again.

splitfires are good on a budget replacement, but dont expect as much out of them as you'll get out of standards

and yes that HKS ignition amplifire is about the only upgrade out there that works successfully for these things

Can i try to start? :)

The plugs were originally 1.1, and gapped down by hand... in the process the head was damaged on one/two of the plugs!

the plugs were fine.. and so end another episode of "name that failure", thanks for playing.

which one of the 3 types of racing plugs from trust do you prefer?

the greddy irridiums are a good budget-ish plug at around $15 each. and the proper greddy racing plugs are excellent but a bit pricey at $25+ each.

the ones i use in the silvia are these ones 13000078 (T7340T-8) and in the GTR the $$$ racing ones are 13000108 (R7419-T8)

I used to think they were just a wank and was happy enough with the $3 coppers, that is until I actually tried them. :)

and yes that HKS ignition amplifire is about the only upgrade out there that works successfully for these things

yep, healthy stock coils and HKS magic gold box is the way to go if you want fat spark. if your stockies fail and you don't want to spend $1500 on new ones then splitfires are not bad but definitely not an upgrade over stock that's for sure.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...