Jump to content
SAU Community

Recommended Posts

krizza_ca18det,

check out myspecv.com

thats a car in the US with the same QR engine.

DOZENS of guys have turbocharged those engines.

a few guys have even used a GT2871r turbo, which is infact smaller than the VG30ET turbo i have sitting infront of me.

Yeah, but the Sentra specV is like the Pulsar SSS of the Sentra range so it wouldn't surprise me if it runs different cams to the X-trail QR25DE which let it breathe better higher in the rev range.

The GT2871r might be a smaller frame turbo than the old VG30ET T3, but it flows a lot more air (400HP rated in 52T 0.64AR trim).

Yeah, but the Sentra specV is like the Pulsar SSS of the Sentra range so it wouldn't surprise me if it runs different cams to the X-trail QR25DE which let it breathe better higher in the rev range.

The GT2871r might be a smaller frame turbo than the old VG30ET T3, but it flows a lot more air (400HP rated in 52T 0.64AR trim).

yeh thats true.

but i know for a fact, the B15 (2000 - 2007) QR25DE used in the sentra is EXACTLY the same engine as the T30 (2001-2007) x-trail's.

same sepcs: 245nm of torque @ 4000rpm, 132kw @ 6000rpm

and very similar torque curves from what i hear, everyone reports the same decrease of power over 5000rpm and the mass amounts of lowdown torque.

i know for a fact the new x-trail's engines are very different from the new sentra's.

the aussie spec qr has a 9.5 CP where as the US spec has 10.5 with completely different internals.

plus the aussie spec was down tuned in 2006 to 125KW due to emissions, and the us spec is rated at 151KW.

with the HP rating, keep in mind im not after mass amounts of peak HP.

maybe 250-270whp at the most, and as you said yourself, my aim is to add mid range.

if things work out well, i might build up then engine including cams and low comp pistons later down the track if im looking for a high rpm monster.

but for the moment, everything's going as conservative as possible. im after driveability in this setup. i just want it to be plain fun to drive - not a 1/4 mile killer or a dyno car...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...