Jump to content
SAU Community

Recommended Posts

On behalf of SAU:SA, we would like to welcome everyone to the launch of SAU:SA, and the first official event of SAU:SA.

DynoDayFlier1copy.jpg

We would like to thank Shannons Insurance, Martini Racing, Geof's Garage and Southern HiTech Dyno Tune for all the sponsorship and support in organising the Dyno Day.

The categories will be:

Highest 6 Cylinder Naturally Aspirated

Highest 6 Cylinder Single Turbo

Highest 6 Cylinder Twin Turbo

Highest 4 Cylinder Single Turbo

Highest Other

Wooden Spoon

There will be trophies and suprises on the day too!!!!!!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/275144-official-sausa-dyno-day-thread/
Share on other sites

  • Replies 443
  • Created
  • Last Reply

Top Posters In This Topic

ummm for now yes might bring the s13 down too but ill let you know later on if theres still a spot left and its not broken haha

thanks cara

ok ill put the R33 down for now :)

1) Cara - R34

2) Kye - R33

3) Vu - R33

4) Ruby - R33

5)Krishy -R33

6)Craig - R34

7)Wayne -R32 GTR

8)Lee - R33

9)Adrian - R33

10)Ben - R31

11)

12)

13)

14)

15)

16)

17)

18)

19)

20)

Try that Vu ;)

ive got a mate with a legnum a rex and a vr4

i dont know if its easy to drop the shafts in them is there going to be a awd dyno?

no there wont be a awd dyno at this event.

Quick Q.

Is the event just for SAU or will other parties be involved ? Like people from other clubs, forums, of the street etc. ?

for the mean time it will be open for SAU people, and then i will re visit the situation on entrants. and the end of the month, and then consider posting on other forums, however, if someone from PGASA wants to be part of the Dyno Day in the mean time, they just need to send me a PM letting me know and ill write their name down on the list :)

1) Cara - R34

2) Kye - R33

3) Vu - R33

4)Ruby - R33

5) Krishy - R33

6)Craig - R34

7)Wayne - R32 GTR

8) Lee - R33

9)Adrian - R33

10)Ben - R31

11)Chad - R32

12)

13)

14)

15)

16)

17)

18)

19)

20)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...