Jump to content
SAU Community

Recommended Posts

Hi what would happen if the car has been run without coolant but the temperature meter (the one next to fuel meter) works like usual?

these are the things:

1) the temperature meter works like the same as when there's coolant in radiator.

takes 5 minutes for cold start to move the needle and 7 minutes to warm up

2) when realise the coolant leak and coolant is dried/gone, why the time for the car to warm up remains the same?

whenever the car is warmed and driving, it reaches half of the temp meter (with or without coolant)

but isn't it when there's no coolant the engine will become overheat and the needle will move up more than half of the meter?

what possible damage has been done to the car or engine? (it has been run for 600kms after last coolant flush during service

throughout these 600kms the car takes the same time to warm up like before

there's no indication that the engine is overheat judging from the temp meter (or was there?) because the needle never moves up more than half

is the coolant temperature sensor faulty?

fyi the coolant leak is between the coolant bottle on the driver side engine bay and the radiator, i am guessing the hose wasn't tightened but will send to mechanic tomorrow since he was the one who last serviced my car

Link to comment
https://www.sau.com.au/forums/topic/276958-coolant-leak-but-no-overheat/
Share on other sites

I used a demineralised water to filled up both the coolant tank and radiator (pour from the radiator cap)

it took about 1.25L for the tank to reach max level and top of radiator.

do you think throughout this 600kms+ drive the engine has been damaged?

hmm the coolant tank on the driver side (left side of engine bay if you stand in front) was empty

coolant was low but didn't know how low

then I refilled with demineralised water on both the tank and the radiator both took 1.25L

I guess if you say as long as there's a few L there gauge should accurate, means the water temp meter is working fine and so as the coolant sensor

I was thinking if there's less coolant needed to be heated, why the required time to warm the engine is the same compare to the past (when there wasn't leak)

I also checked the engine oil and it remains at H

Hi the coolant level has ocassionally gone down a bit.

During very cold weather, ocassionally (I mean it doesn't usually happen but sometimes it just happen), when the car is started and the weather is cold (eg in the late night or early morning), there's white smoke coming off. However when you drive away, the smoke is gone.

to describe it more detail, it only happens during warm up.

process: start car, no smoke, after a while waiting for car to get warm, then smoke, drive away, smoke is gone.

Mech has put 1bar pressure on the radiator cap and it holds the pressure, so he said it is fine and gasket has no problem.

The thing is, why only cold start? and it does not happen when car drives away or in later start.

is my gasket fine?

I would say the level of coolant in radiator remains high to the top but the level of coolant in the tank on driver side has gone down a little.

hose is tight, cat converter is fine (was checked few days ago), engine oil level is fine.

so what is the problem?

also the coolant has no discolouration (remains green after top up with demineralised water)

Edited by KJS

no there's no coolant leak on the floor.

now I am only worry about:

is my engine burning coolant? why ocassionaly there's smoke during cold start (I don't think it is condensation because the coolant level in tank has decreased a bit, maybe 1-2cm from the max but radiator only drop a tiny bit), and yes I top up the coolant to check this and only manage to discover the slightly lower volume after seeing smoke happen

also when I started the car, the coolant in the radiator didn't have bubbles or the coolant amount didn't drop (of course that time also didn't have white smoke)

so it does not always happen, it happen ocassionally

you reckon I don't need to worry? I just feel worry because I am afraid a hidden problem might be there just that I don't know.

when you start your car on a cold day you will always get condensation, it will not lower your coolant level... smoke is smoke and condensation is condensation... can you smell smoke?? is it white or disappears?

plus when you first start your car there is no way it would overheat straight away.

From what you have explained it sounds like condensation on a cold day. unless you can explain in more detail i don't think you need worry.

at first I thought it is condensation, because of the cold weather.

but the smoke is a bit too much and the wind will blow to the front passenger screen

however the thing is, I cannot define it as blown gasket because when I starts driving the car, the smoke will be totally gone.

and most the time it will not happen again in next start up, or even next cold start

it happens occasionally

sometimes even if the night is cold, it doesn't happen

the unpredictable manner makes me think this is worth to be worried.

if the cold night has smoke, next morning when I check the coolant level of the tank on left side (driver side), it is lower than the H level

but when I open the radiator cap, it is still full or maybe insignificant drop.

now I am not worried about whether the engine has been overheated

but I am wondering why the coolant level has dropped

I mean randomly dropped

and random white smoke

I think you should see small bubbles coming through the radiator(with radiator cap removed) when you repeatedly crank an engine with a blown head gasket. Is this true, maybe im wrong?

EDIT: just thought about it and this is a trick used in darwin where some cars have themostats removed. ie probably wont work if thermostat is closed.

also i recently had a radiator leak and the first radiator pressure test conducted by a workshop that specializes in radiator repair *apparently* held pressure even though coolant had literally drained from the stationary car. I told them to do it again and then they found it had a crack. They never charged me for the test and I took my radiator elsewhere to be fixed.

Edited by brent32
I'd been told that if there was some coolant already in there, then using plain old water wouldn't adversely affect it for a top up? I was hesitant to do that to mine for fear that it would corrode the insides of the radiator.

No not too bad if it's got coolant in there your just diluting it. allthough it's better to top up with demineralised water rather than tap water. obvious reasons.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...