Jump to content
SAU Community

Recommended Posts

As topic says I am a noob, so please no flamming :)

This morning car felt fine, this evening went out and when I put my foot down to accelerate there is no power when the turbo usually kicked in at 2500 rpm. I haven't done anything differnt than earlier in the day. The turbo gauge is going from -1 to 0 and no further. Had a quick look under the hood and couldn't see any leaks etc. Any idea's what could be going on?? Im thinking a trip the mechanic is in order.

Thank you for any advice

Link to comment
https://www.sau.com.au/forums/topic/276975-noob-with-turbo-problem/
Share on other sites

I concur with hyper gear, take of the dump pipe and look at the exhaust wheel

Im assuming this would have been the first thing you would have checked and as noone else has mentioned it have you checked all your cooler piping. When they blow off they can make a loud bang and then no power. Other than that it sounds like it icould be a turbo matter.

could also be a wastegate issue. if the wastegate is stuck open then that will dramatically affect performance. i had a boost controller once that would hold pressure between it and the wastegate so when you changed gears you would have no boost in the next gear.

so undo your wastegate actuator and see if it is moving freely.if it is, then also check you vaccum lines to make sure there are no blockages between the wastegate and the intercooler pipe.

then if that is still ok then pull off your dump pipe and check the exhaust wheel

could also be a wastegate issue. if the wastegate is stuck open then that will dramatically affect performance. i had a boost controller once that would hold pressure between it and the wastegate so when you changed gears you would have no boost in the next gear.

so undo your wastegate actuator and see if it is moving freely.if it is, then also check you vaccum lines to make sure there are no blockages between the wastegate and the intercooler pipe.

then if that is still ok then pull off your dump pipe and check the exhaust wheel

+1

Im assuming this would have been the first thing you would have checked and as noone else has mentioned it have you checked all your cooler piping. When they blow off they can make a loud bang and then no power. Other than that it sounds like it icould be a turbo matter.

Nope, it wouldn't be the cooler piping as the slightest leak in the cooler piping, and the car will not idle normally.

The fella mentioned it's idling normally....

Either the gate is stuck open, or the turbo is f'd

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...