Jump to content
SAU Community

Recommended Posts

Hey guys,

I've just purchased a complete R34 that i'm parting.

- Pair R34 Xenon's + loom for a R34 light conversion (inc. plugs / ballast / bulbs) $1500 AU

I'm located in Auckland, NZ so i'm only able to ship smaller parts. Anything to large to send won't be for sale here.

But PM me or reply here on any parts you want.

- Tiptronic

- RB25de

- 110000 km's

- Pearl White

71198351.th.jpg

72265125.th.jpg

Cheers :laugh:

Edited by Chang
Link to comment
https://www.sau.com.au/forums/topic/277068-wrecking-complete-r34-sedan/
Share on other sites

Hey guys,

I've just purchased a complete R34 that i'm parting.

- Pair R34 Xenon's + loom for a R34 light conversion (inc. plugs / ballast / bulbs) $1500 AU

I'm located in Auckland, NZ so i'm only able to ship smaller parts. Anything to large to send won't be for sale here.

But PM me or reply here on any parts you want.

- Tiptronic

- RB25de

- 110000 km's

- Pearl White

71198351.th.jpg

72265125.th.jpg

Cheers :laugh:

INTERESTED IN XENON LIGHTS...STILL AVAILABLE?

Sorry Rance, Bonnet is too large to send via NZ to AUS.

lanky71, Xenon headlights are gone. But I still have a set of Non-Xenon's available.

666dan, yes it does have the cup holders. But going with the centre console.

But I have Pm'd the rest of you guys.

Edited by Chang

Here's a rough price list

Exterior:

Left / Right Non-Xenon headlights $1000

Left / Right wing mirrors $200

Monsoon / whether shields / wind deflectors $100

Rear wiper + motor + loom $100

Tail lights (tinted lenses) $160

Interior:

Airbag system (complete) Tiptronic steering wheel / Passenger airbag / Airbag computer $500

Air con unit (damaged face plate but still working fine) $60

A pillar trim + boost gauge (not branded) $80

B pillar trim (lower centre trim) $80

C pillar trim (rear where rear seat belt comes through) $80

Centre dash vent $80

Centre console (with leather lid / compartment) $120

Complete set (5x) seat belts inc. bolts and buckles $200

Door sill trims $80

Speedo cluster surround $60

Tiptronic shifter $100

Tiptronic shifter surround + ash tray $80

Tiptronic cluster, approx 110,000 km’s $150

Misc:

RB25de Neo ECU computer $100

Edited by Chang
Sorry Rance, Bonnet is too large to send via NZ to AUS.

lanky71, Xenon headlights are gone. But I still have a set of Non-Xenon's available.

666dan, yes it does have the cup holders. But going with the centre console.

But I have Pm'd the rest of you guys.

What if I supply you with the factory 'blank plate' that normally sits in that location? Then the centre console is still complete for you to sell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, I’ve just finished fitting the timing belt on my RB25, following the standard procedure: rotate the crank twice, release the tensioner, then tighten it down. The belt feels tight, and you can see that clearly in the picture below I’ve heard some people say it’s actually better for the belt to be slightly loose rather than too tight, as excessive tension can lead to snapping. So that’s in the back of my mind. What I’m seeing is this:  • At idle, the belt looks fine.  • But when cranking and especially when revving (around 3–4,000 RPM), there’s a momentary flap/flex or flicker in the belt, which I’ve tried to capture in the video. So my question is — based on what you see, is this slight belt movement something you’d consider normal, or am I just being OCD? Could this amount of movement cause sync issues? Or is it just a harmless bit of flex under load?   from what I know belt flap and flex is expected when crank spins up and pull cam with it Would appreciate any thoughts or similar experiences.     IMG_7656.mov IMG_7657.mov
    • I've replaced the front brakes of my NA to 324 brembos and 350z calipers: i'm going for 225/40-18 up front and 245/35-18 in the back. I have Rays 7.5*19 ET35(225/35) in the front with 5mm spacers otherwise the calipers "lock up/ won't rotate". When i use the calculator i come up with 8*18 ET30 for 225/40...... but not sure i get problems with the calipers. Anyone riding around with 18 inch. that can confirm "that it'll fit"? In the back it's 7.5*9 ET30 (245/30) with the 5mm spacers, but there is no problem with the standard small brakes, so i want to take 8.5*18 ET25 (245/35).
    • Lol.. but then.. always come back to a JDM..
    • Glad to hear. If possible, get your tuner to check air's to make sure everything is still where it should be.
    • The problem with FB/Insta/Reddit etc comments relating to cars is simple. You get to ask a question once, and get one round of replies. For things that can actually be answered in a few lines of text, once, it's fine. After 6 hours, your original question is lost to the void. There are no follow ups, additional questions, anything. No project car is ever such a simple list of questions to ask. You need discussion.
×
×
  • Create New...