Jump to content
SAU Community

Recommended Posts

hey guys

ive had really bad fuel milage (approx 280kms a tank)

anywho i was thinking it was the o2 sensor, but when driving home from work i watched the stock boost guage closely.

at normal cruising, it sits close to -6 but once a bit of throttle is put on (below 2.3-3000 revs) it moves up to 1/4 mark and somtimes 0.

am i getting constant boost? i know a turbo works on exhaust gases but i dont know much about the factory boost guage.

Link to comment
https://www.sau.com.au/forums/topic/277342-think-im-gettin-constant-boost/
Share on other sites

your only getting boost when the gauge starts going above 0 into the positive area, sounds normal to me.

try new plugs, fuel filter, clean out you throttle and AFM and swap your O2 sensor, should get you out of trouble

yeah it is, running stock boost too i think so 5psi or whatever it is.

just wanna know why i got such bad fuel consumption, i know skylines are a performance car but 280kms out of a full tank still?

and thats not floggin it every time either

^ exactly - the list is long.

The answers are plenty however - please do a search.

Its been covered pretty well as you could probably imagine... being fuel economy is a reasonably big problem for most people

sounds like the turbo is spooling up but, even when under the 0 in the negative side

yeah my car does the same thing, but its just the pod filter sucking air in, you can tell the difference between the induction and ur actual turbo spooling

Do all your regular maintenance as per the many threads covering this article, don't bother trying to work anything out until it's fully serviced then go from there.

An important thing to note is cold and hot starts as was mentioned above. All cars use more fuel when running cold so if you;re ot trips your fuel economy will suffer badly.

Get used to high fuel consumption. 280km is low for sure but your never going to get fantastic results. I went from a 3L v6 magna to the skyline and the magna despite being 500cc more drank SO much less fuel.

Also given that you have had the car for such a short period of time, is it possible that you have just been enjoying it quite a bit, ie giving it a bit more throttle than normal, going for short cruises around the block etc? When I first got mine the whole turbo thing was awesome fun but led to driving in a way that was very harmfull to the consumption.

as mentioned before ^^^

just give your car a decent service, change all the fluids, spark plugs, give the afm a decent clean....warm it up and then go for a nice drive....dont thrash it just drive it normally and let things smooth out.....you might notice a bit of a difference in consumption....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I think the concept is highlighting the various scenarios where thicker oil helps, and thicker oil potentially doesn't help and only generates heat and costs power, in turn for safety which isn't actually any safer (unless you're going real hot). If anything this does highlight why throwing Castrol 10w-60 for your track days is always a solid, safe bet. 
    • Jason should have shown a real viscosity vs temp chart. All the grades have very little viscosity difference at full operating temperature.
    • Oops... I meant to include the connector  view... BR/W - power from fuse L/W - motor negative to fan control amp (and off to HVAC pin19) OR/B - PWM signal (from HVAC pin20) B --  ground  
    • Yep, if you are applying filler it sounds like there is something wrong with the body lol. Safe to assume there is going to be a lot of sanding going on if your still applying fillers.  Picture a perfect bare metal panel, smooth as glass. You lay down your primer, it's perfect. (why are you going to sand it?) You lay down the colour and clear, it's perfect. No sanding at all took place and you've got a perfectly finished panel.  You won't be chasing your tail, sounds like you were prepping to start laying filler. If your happy with the body after the sanding, there is some bare metal exposed and some areas with primer, no issues at all, start laying the filler. You are safe to lay filler on bare metal or primer (of course check your technical data sheet as usual for what your filler is happy to adhere to).  This isn't a 100% correct statement. There is primer that is happy to adhere to smooth bare metal. There are fillers that are happy to adhere to smooth bare metal. Just make sure you're using the right materials for the job.  Typically if you are using filler, you would go primer, colour and clear. I've never seen any instances before where someone has laid colour over body filler (maybe this happens, but I haven't seen it before). So your plan sounds pretty normal to me. 
    • I don't think there's any way someone is push starting this car.. I honestly can barely move it, and moving it and steering it is just flat out not possible. I'm sure it is, but needs a bigger man than me. I have a refurbished starter now. The starter man was quite clear and consise showing me how nothing inside a starter really should contribute to slow cranking, and turned out that for the most part... my starter was entirely fine. Still, some of the wear items were replaced and luckily it didn't show any signs of getting too hot, being unfit for use, etc. Which is 'good'. I also noticed the starter definitely sounded different, which is a bit odd considering nothing should have really changed there.... Removed and refit, and we'll pretend one of the manifold bolts didn't fully tighten up and is only "pretty" tight. GM only wants 18ft/lb anyway. I also found a way to properly get my analog wideband reading very slightly leaner than the serial wideband. There's Greg related reasons for this. The serial output is the absolute source of truth, but it is a total asshole to actually stay connected and needs a laptop. The analog input does not, and works with standalone datalogging. Previously the analog input read slightly richer, but if I am aiming at 12.7 I do not want one of the widebands to be saying 12.7 when the source of truth is 13.0. Now the source of truth will be 12.65 and the Analog Wideband will read 12.7. So when I tune to 12.7 it'll be ever so slightly safer. While messing with all of this and idling extensively I can confirm my car seems to restart better while hot now. I did add an old Skyline battery cable between the head and the body though, though now I really realise I should have chosen the frame. Maybe that's a future job. The internet would have you believe that this is caused by bad grounds. In finding out where my grounds actually were I found out the engine bay battery post actually goes to the engine, as well as a seperate one (from the post) to the body of the car. So now there's a third one making the Grounding Triangle which is now a thing. I also from extensive idling have this graph. Temperature (°C) Voltage (V) 85 1.59 80 1.74 75 1.94 70 2.1 65 2.33 60 2.56 55 2.78 50 2.98 45 3.23 40 3.51 35 3.75 30 4.00   Plotted it looks like this. Which is actually... pretty linear? I have not actually put the formula into HPTuners. I will have to re-engage brain and/or re-engage the people who wanted more data to magically do it for me. Tune should be good for the 30th!
×
×
  • Create New...