Jump to content
SAU Community

Recommended Posts

Depends where you get them from.. about 4.5g to 5g AUD for brand new 2 x gt-rs. I would assume similar price for hks twin 2530/2540. :) Works out almost the same price if you order two garrett gt25 thats rated to 400hp with similar a/r housings... :)

Link to comment
https://www.sau.com.au/forums/topic/27830-gtr-performance/#findComment-581628
Share on other sites

That's right, for 300kw at the wheels you will need the following.

Bigger turbos say 2540's, power fc, cam gears, injectors, rail, pump, regulator, exhaust, bigger cooler & probably suggest some coils and a bloody good tuner. You can pretty well get to 270kw at the wheels with out doing the fuel system but again you need a good tuner. Bottom line is you need money.:uh-huh:

Link to comment
https://www.sau.com.au/forums/topic/27830-gtr-performance/#findComment-582991
Share on other sites

Ive got an R32 GTR with 2530's and power fc (and avc-r) and my god it flys, as you probably should be able to tell by my smashed gearbox and clutch :rolleyes: (quarter mile attempt #1 gone wrong)

The car made 309kw on a dynopak dyno, so this is around the 280-290kw mark at all wheels. It was a pretty good tune I guess now (in hindsight), car never detonated, but I was frequently getting warnings from the Power FC that the injector duty cycle was 90%+ when I was full throttle coming upto 7000rpm. My advice would be;

Power FC, HKS 2530/GT-RS, HKS adjustable cam gears, new fuel pump, new injectors and if youre budget can stretch it, a HKS step 1 (256 degree) exhaust camshaft... the exhaust camshaft makes quite a large power difference, and on a similar setup to my car previously, would make 50kw more at the wheels than the best I could do.

Link to comment
https://www.sau.com.au/forums/topic/27830-gtr-performance/#findComment-583231
Share on other sites

Ive got an R32 GTR with 2530's and power fc (and avc-r) and my god it flys, as you probably should be able to tell by my smashed gearbox and clutch  (quarter mile attempt #1 gone wrong)

did you use the standard exhaust and cooler ?

Link to comment
https://www.sau.com.au/forums/topic/27830-gtr-performance/#findComment-584177
Share on other sites

Hmmmmm. 300 rwkw cheaply...

I would go for a pair of N1 turbos (or standard turbos with N1 internals) around $2200. Bolt straight up, saves heaps on pipework and fittings.

Pair of split dump pipes say $700.

3" engine pipes and 3.5" exhaust $900.

Bosch 044 motorsport fuel pump $400.

Adjustable Sard fuel pressure regulator $350

Standard injectors OK, with 10% overdrive using higher fuel pressure.

Used set of HKS 264 cams say $800

Standard intercooler OK

That totals around $5500 plus fitting (if you can't do it yourself) and tuning. Sounds about right.

It would have good average power as well, not just a peeky 300 rwkw at one single rpm point.

Hope that helps

Link to comment
https://www.sau.com.au/forums/topic/27830-gtr-performance/#findComment-584517
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...