Jump to content
SAU Community

Recommended Posts

u can get it for around $500 or less if u get it off nissansilvia.com, or even a trader off here will have a deal that is cheaper than what u have been quoted b4. off the top of my head for the same clutch u mentioned it was about $496 + $20 postage off ns.com

" Pressure plates and clutch plates provided with these clutches are oem bundled released direct from Daiken, RPM or Seco and are not Pink or Purple like the boxed Exedy items unless listed as Exedy."

Make sure you get EXEDY .. I only use the pink clutch covers with pink cushioned button clutch plate

I'm running 360hp in mine with a twin plate clutch, handles beautifully. Though every once in a while it does grind a little heh, fkn noisy twin plates...

Was looking at getting one of these if mine ever fries.... http://www.nengun.com/exedy/hyper-carbon-c...in-plate-clutch mmz.

Tenegah have a deal on supply and fitting of genuine Exedy's

http://www.skylinesaustralia.com/forums/Ex...rt-t279096.html

Be very careful of some of those "too good to be true" prices, as quite often they use some non-genuine parts in there kits.

^^ sounds good to me, am i doing any damage to my car driving it with a very slipy clutch? dont have the funds to buy 1 for a couple of weeks

cheers

You won't be doing much damage, but don't drive it too hard. Tenegah will have your standard flywheel faced, so it should be as good as new :D

i remember a thread created by someone who discussed all the different types of clutches with their pro's and con's. anyone know where this has gone???

i need a new clutch for rb20 and heard twin plates faark rb20 gearbox's so researching on whats best

anyway ideas???

I've got an Rb20 turbo 5spd in my ceffy, and i can tell you that if i had a twin-plate, i'd be on the side of the road still. a single plate heavy duty organic is the go for that particular gearbox.

ring auto clutch in osborne park. got one of his clutches behind my 25, feals like standard and takes anything stock internals can throw at it for around $300-350 with machined flywheel, thrust bearing and spigot bush

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...