Jump to content
SAU Community

Recommended Posts

I'll take pics of it tomorrow and you tell me maybe, or maybe I could look at my C210 service manual ans do some checking for myself eh!

The part I have is out of a KDR30.

Ummmmmmmmmmmmmm, bugger it, I'll take the piccy now.

BBS, D

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

D, the 260 is like your one, also symetrical. There is no other option than to have one made. I took it to a spring place today. They think they can do it and it'll be around the $200 mark. I also had my mate who sold me the 260Z shafts ring me , as he has someone wanting a R200. Wanted to know if I'd sell it. I was for a moment tempted and if it was'nt for me really really wanting LSD, it might have been different.

On a brighter note, my strut brace turned up today( shit I have'nt checked to see if it fits). Back soon

D, the 260 is like your one, also symetrical. There is no other option than to have one made. I took it to a spring place today. They think they can do it and it'll be around the $200 mark. I also had my mate who sold me the 260Z shafts ring me , as he has someone wanting a R200. Wanted to know if I'd sell it. I was for a moment tempted and if it was'nt for me really really wanting LSD, it might have been different.

On a brighter note, my strut brace turned up today( shit I have'nt checked to see if it fits). Back soon

Pheewww, it fits.

And would any of them be 4.1?

Got 2 x 4.11 & 1 x 3.9:1 but none for sale.

I am trying to swap a 4.11 for a 3.9 with Stewart Wilkins because I want a 3.9 for the PNV and both for the DR.

A bit of advice for you Ricky, before you put your diff in, get it sorted by an good diff guy, because they were a sales gimmick more than a performance option. You will want the clutch shims operating at about 70lb, otherwise it will be an expensive single spinner. The pre load stock is about 20lb which is SFA.

I have a Cusco 4.11 with about 75-80lb pre load that is destined for the DR for the October 4th Oran Park track day in NSW.

Cheers, D

My "spin" on R30 R200 LSD's .

From the factory I think they only had one set of active plates in both sides where the Nismo ones had I think four sets . They also have a steel disc in each side that you remove which makes room for the extra plates .

I had AJ pull mine down and fit the extra plates and it's pre load was ~ 65 lbs static (DR30 rear end in Bluebird) .

Even this for road only was possibly a little high and around 50 may have been better .

What it used to do was load up the center in first gear 90 degree take offs and judder a bit due to reduced differential action .

The Ghost has my spare R200 R30 driveshafts .

PM Dennis .

Cheers A .

WHAT!! you mean I gotta spend more money again. So what'll happen if I just install it and go launching in it? don't tell me i'm going to break it. So now I need to install some plates. Will a difff place tell me what the current static lb is. F$%#K me this had better be worth it, like dropping a whole second of my 1/4 mile time.

L.S.D= LOST SHITLOADS of DOLLARS

Sorry Ricky,

Welcome to the land of high performance motoring!

R200 LSD's are fantastic bits of equipment, but they cost money to set them up right. They are the Japanese equivalent in IRS to a Ford 9 inch & virtually indistructable. You can break the gears (crown wheel & pinion) but never the LSD hemisphere which can be swapped from diff to diff.

And any spares I have are being kept now I have a track car too!

Cheers, D

New moustache bar was completed today, unfortunately I can't pic it up till Monday due to work. They haven't worked out the price yet.

Also ordered new rims, 16x8 superlites, -4 for the back and 0 offset for the front. Hoping to run 235/45R16 on the rear and 205/50R16 on the front. Slowly it's coming together. I'm also getting the car repainted in ?????? colour.A friend of mine has almost finished his new workshop out on some acreage, he's an ex spray painter. He's talking $1500 as there isn't too much prep as my acrylic is in good nick. I' still haven't buffed it back yet, now there's no need, even better.

  • 2 weeks later...

Farrrrrrrrrrrrrrrrk!!! excuse the outburst of total, and absolute frustration.Straight bolt in! where's that f'n gun. After hours of toil under the car, I got the R200 in complete with new moustache bar which actually does fit.Went to bolt the driveshaft to the pinion drive flange on the LSD and guess what? they're totally different sizes. The 4 little nuts and bolts don't line up at all.Farrrrrrrrrrrrrk again. Now I'm going to have to some how modify my driveshaft flange to suit the R200 flange. Got to say it again Faaarrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrk!!!!!!!!!! Don't suppose this has happened to anyone else by coincidence?

this site s kinda lame, but shitcans of info and pix

go right through this

http://project240k.com/

particularly

http://www.project240k.com/index.php?optio...9&Itemid=29

Considering the scope of the engine upgrades planned for the car, i had started to do some research into how i could get some traction out of the car. For this, i figured i needed an LSD differential.

My two main options were to either try and find an R180 LSD (R180 is the standard Differential for the 240K) or to find an R200 LSD differential. The R200 is huge in comparison to the R180, and comes in 2 versions, the Longnose R200, used in 260Z's and import R31 Skylines, and the short nose R200; in most 90's nissan performance cars (Skyline, 200SX etc.).

LSD 180's and long nose R200's are really hard to find, with many going for over $1200 second hand (and with no guarentee of working), and although short nose R200's are wasier and cheaper to find, it wasn't clear how easy it would be to fit the LSD core between a short nose and long nose (afterwards, i found this great site:

I managed to track down an open R200 Differential from a 260Z relatively cheaply, whilst it isn't LSD, i can worry about that minor detail later.

The long nose R200 fitted really well in place fo the R180, with the only modification required being a custom moustache bar for the rear. The R200 i bought took uni-joint half shafts, and i will look into converting these to CV's later on (for more power handling)

http://www.project240k.com/index.php?optio...7&Itemid=34

Ricky - that really sucks about the flanges. I feel sorry for not doing more research about R200's before recommending you go down this path.

This won't make you feel better at all, but out of interest I pulled a (Datsun) univesal joint driveshaft out of my (Subaru) clircip-type LSD and had a look at how my diff guys got the damn thing to stay in place without it falling out.

Turns out there is provision for the bolt in there. Either the subaru R180 diff comes with a redundant bolt hole, or the diff guys recycled some of my Datsun diff centre. For being so ignorant about how to cobble together diffs from various models it looks like I got off lightly compared to the headaches you have been having.

I did Ghostriders trick of jacking up the rear, and both wheels turned, so it is an LSD, not the original open-wheeler.

post-26626-1249285737_thumb.jpg

post-26626-1249285814_thumb.jpg

Thanks for the words of sympathy Drew, I also should've rung around and found out the pros and cons of undertaking this task. After reading about your recent pains my probs don't seem so bad. At least my motor still kicks ass. Also today my friend who builds up Z cars told me he can change the drive flange on the R200 to suit my tailshaft, this could finally be the end of my probs. Rick.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...