Jump to content
SAU Community

Recommended Posts

Picked up my new coilovers for the Stagea today!

As long as im not too busy tomorrow I will install these puppies myself!

They are the Tanabe Sustec Pro NF models - so no rebound or preload damping, but height adjustment. They are meant to have a similar spring rate to the standard shocks, but damping is a little heavier so it doesnt sway and bounce so much.

Quality looks great - So I hope they perform.

Once these are set, Ill pick up some rims to really set the car off :)

Has anyone installed shocks on the M35 before? Fronts shouldnt be too hard, but im worried that my cheap Auto 1 spring compressors wont be good enough for those rear springs.

Pics of before and after up tomorrow hopefully!

Ben.

post-4475-1247554540_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/279114-got-some-tanabe-for-the-m35/
Share on other sites

As long as you have the tools:....you will need rattle gun from memory.

Front is easy....make sure you compress you springs first.

: Three bolts on the top of the shock in the engine bay

: One bolt on the bottom on the suspension.

: One bolt on the strutt and one clip from the brake lines

: Pull the lot out then undo the clamp on the bottom holding the shock on.

Rear

Little lost with your rear shock or my memory is gone.

It's a pretty easy job....I did it by myself in about 2 hrs.....you WILL need a wheel alignment after though.

As long as you have the tools:....you will need rattle gun from memory.

hhmmmm I dont have a rattle gun, just my trusty socket set! haha Fingers crossed that will be enough.

Did you have to pull any interior out to access the rear strut bolts. I only peered under the car, and it seemed like I may be able to remove the shock from underneath.

Thanks for all your info though. I appreciate as much as I can get before pulling bits out.

hhmmmm I dont have a rattle gun, just my trusty socket set! haha Fingers crossed that will be enough.

Did you have to pull any interior out to access the rear strut bolts. I only peered under the car, and it seemed like I may be able to remove the shock from underneath.

Thanks for all your info though. I appreciate as much as I can get before pulling bits out.

The rear is all external, no trim to remove at all.

The shock is the easy part as the top of the shock bolts on to a "top hat" that sits in a recess and is bolted in place. Really easy part.

The harder part is compressing the rear spring getting it to sit in the separate seat for the spring. When Sydneykid helped me with my rear we undid the bolts in the inside of the spring cradles so that it dropped down towards the wheel before we positioned the spring and then pushed it all back up into place. If you remove this bolt pay attention to it's orientation as it is ekcentric and adjusts the toe in.

Cheers

Andy

The rear is all external, no trim to remove at all.

The shock is the easy part as the top of the shock bolts on to a "top hat" that sits in a recess and is bolted in place. Really easy part.

The harder part is compressing the rear spring getting it to sit in the separate seat for the spring. When Sydneykid helped me with my rear we undid the bolts in the inside of the spring cradles so that it dropped down towards the wheel before we positioned the spring and then pushed it all back up into place. If you remove this bolt pay attention to it's orientation as it is ekcentric and adjusts the toe in.

Cheers

Andy

Thanks for the heads up andy! I was planning on doing it that way, but wasnt aware that the bold was eccentric! thanks for that :D

Benny, word of warning: once you have your springs compressed, DO NOT have them pointing towards you at ANY time. It's the equivalent of having a gun or rifle pointing at you, if the spring compressors fail, then the spring can pop out with enough force to kill you, NO JOKE.

As far as not having a rattle gun, if you have a strong piece of pipe you can put over the end of your socket spanner or breaker bar, you *should* be able to get enough leverage to crack loose those stubborn nuts and bolts.

"Benny, word of warning: once you have your springs compressed, DO NOT have them pointing towards you at ANY time. It's the equivalent of having a gun or rifle pointing at you, if the spring compressors fail, then the spring can pop out with enough force to kill you, NO JOKE."

agreed! I had a close call with a mate, scared the daylights out of both of us!

so if you remove the shock and lower the LCA all the way down, the spring still wont slip in?? i thought with a shorter coil it would be easier to get in. then just use a jack under the LCA to push it back up to a point where you can bolt the new shock in

Well I successfully fited the coilovers today!!

Although its a little too low at the front - looks awesome, but when I got home I hit the front lip and undercarriage pretty bad getting into my unit blocks crappy driveway entrance.

Fitting took me a solid 3-4 hours - mainly due to the cheap spring compressors being a nightmare to work with and bending enough to scare the hell out of me! haha

The Tanabe's are great quality and everything lined up and slotted into place perfectly.

The ride is very simillar to the standard shocks, but you notice the stiffer damping when cornering - you also notice its not quite as supple on really bumpy rough roads.

So I'm really happy with it, and the car looks so much more aggressive low to the ground ;) Hope to have some rims fitted in the next couple of weeks - the standard wheels look exceptionally skinny and small all of a sudden!

Pics up later tonight.

Ben.

Ben, ive been looking for some shocks for a while and I couldn't find much without importing. Were these bought locally? If you dont mind telling us all, how much was the set and where did you purchace?

Although its a little too low at the front - looks awesome, but when I got home I hit the front lip and undercarriage pretty bad getting into my unit blocks crappy driveway entrance.

Welcome to the lowered suspension / factory aero kit combo :blink:

Be prepared to scrap often :O ... why not.... i do ;)

So Here are some pics of the car before and after:

Before Front: post-4475-1247695625_thumb.jpg After Front: post-4475-1247695633_thumb.jpg

Before Rear:post-4475-1247695652_thumb.jpg After Rear: post-4475-1247695662_thumb.jpg

As you can see the front lip is a little too low now. I think Ill be lifting the front a few cm and dropping the rear a cm on the weekend.

post-4475-1247695691_thumb.jpg

Here are the shocks in place. Alot easier to fit these than remove the originals!

post-4475-1247695669_thumb.jpg post-4475-1247695684_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...