Jump to content
SAU Community

p plate driver driving skyline gts-t


Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Its a good question..

But its a stupid law (power/weight) .. how on earth can they enforce it? UNless they demand an on the spot dyno check. If not, you can easily detune your car to run lower power.

Same with insurance companies, they wont be able to enofrce it, so I doubt it comes into play.

If your car isnt on the list on vicroads, then id say your safe.

Ask your insurance company.

Originally posted by ex-static

I got pulled over last night for a 'routine license check' while I was dropping my mates home.

It was 12 at night and I didnt have my license on me, nor P plates.. the copper was pretty nice, and was more interested in how a 'p plater' could afford a car like this. But he was still a bit pissed at me because I didnt have my p plates up, and I got a $105 fine. I have to take my license in this afternoon.

He didnt mention anything about not being able to drive it, but he did look a bit stunned at the SAFC on my dash, and the Electronic boost controller idling away.. oh, and the boost guage mounted on my pillar.

I just think he was bored and wanted to check out my car.

Oh.. and fine me :D

You're lucky, for not having your p's up its a one month suspension, and a 500 buk fine, and not haviong your licence is a 50 buk fine, consider yourself lucky man.

It is legal to not carry your liscence on you, they can't get you for that...

My friend got pulled over for a roadworthy check, he has an immaculate looking BMW E36, The cop didn't mind that he didn't have his liscence on him. My friend found it funny that the cop wanted to get in to rev the engine to see if there was smoke coming out of the exhaust...

Winfield, you said in the first thread:

134kw per tone base on the power output as 184kw and 1370kg.

134kw is more than 125kw. The car is P plate restricted. Full stop, end of story. Reguardless if its on that 'list'.

Wether or not the police will enforce the rule (like any other) is a completely different story. Most of the time they will, coz they can (bastards!).

A mate of mine was pulled over driving a WRX on his Ps and lost his licence for 3 months.

At the end of the day, if you want the car, get it. Dont let the first few years of P plate hell ruin your dream. Skylines are fantastic!

well i moved up north from melb in december last year but... I was pulled over driving an STi and an S2000, both I beleive are well over the power to weight ratio, and I was wearing P plates in both instances.

Neither time did the police even mention it being to powerful. First time when I got pulled over in the STi, the cop wanted to know how I got my hands on 1 of 400 of the 4 doors and how it went etc... and the time I got pulled up in the s2000, the cops were joking that I must have robbed a bank to get an 80grand car on my P's.

Be polite & respectful and they tend to leave u alone.

well i actually have a NSW license.. as im in Tweed heads. (right on the border) and to tell you the truth I really wouldnt know..

Havent been pulled over since I have been here, but have driven the new wrx, the new wrx STi, cv6 & cv8 monaro, silvia s15 etc and never had a problem with the police - so I guess they dont have the rule or they just dont give a ****.

But yeh - i was kinda crapping my self with the STi as I did a bit of 4 wheel drift from malvern road into chapel street at 2am on a week night and there was a bloody cop sitting at the lights. I just said "sorry, only just got the car today and didnt realise the power it had". Cop was just asking about how i got the first one etc etc and then let me off with a warning for doooorifting :D

  • 1 year later...

i wouldnt care if i was you...vast majority of p-platers driving high powered cars now

Ive been pulled over 3 times in the past 2 weeks

They have looked under my bonnet everytime, with a nice big pod hanging out right in front...out of all 3 times they just asked me how many turbos do i have and thats about it.

My car is pretty sleeper style, the fmic is hidden same with my other stuff, most of em dont know wat the **** they are looking at and always ask me wats that and wats this etc lol

u dont get hassled much at all, as long as u dont bring attention to urself :D

P.S im collecting the Breath tester tubes thingys...ive got 3 now lol does anyone else keep theirs ?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...