Jump to content
SAU Community

Recommended Posts

I washed my engine bay down on Tuesday earlier this week.. Car is running like its dropped cylinders.

I have put the ignitor and coilpack looms on a GTR and it ran perfectly fine so I know they are ok.

I have replaced the airflow meter also

I just got a set of secondhand coilpacks and before installation diagnosed cyl 1 and cyl 6 have wet plugs.. so I replaced number 1 & 6 coilpack.

plugs are still wet and runs the same..

swapped number 1 plug into pot 2 and vis-versa to check that plugs were not faulty... number 1 is still wet and so is pot 6

where do I go from here... CAS? ECU? there is alot of fuel smoke coming out the exhaust also, guess thats because the oxy sensor thinks its running lean?

Edited by BANGN
Link to comment
https://www.sau.com.au/forums/topic/281465-rb20-missing-like-a-dog/
Share on other sites

injector would not do it.

have you checked all intercooler and intake plumbing is not leaking and all done tight.

check you afm plug, makesure the afm is nice and tight in the intake and sealing up.

other wise might still be some water in the look some were.

good luck with it all

Decided to run the car up again and rap the throttle a couple of times and very swiftly pulled all the plugs again.

1 - Dry & Black

2 - Wet & Black

3 - Dry & Black

4 - Dry & Black

5 - Dry & Black

6 - Saturated and Black

So I put the plugs from 2 & 6 next to eachother in 4 & 5 and ran the car up... only 4 & 5 are wet.. so its either plugs or coils.

- replaced the coils in 4 & 5.... the plugs are still wet.

- pulled the plugs out of my miss's daewoo and replaced 4 & 5 only, started it up and ran smooth then started getting rough and smokey again (plugs were rather different tho, but they still pulled out wet)

- put my plugs back in but swapped 1x wet plug to cyl 2.

- cyl 5 was dry but cyl 2 was slightly wet.. but the car ran smoother and I think smoked less. (I asume this is because because the faulty cyl's were spread out now making the motor turn over smoother)

replace all the plugs you think?

Edited by BANGN

well I am getting somewhere now.. replaced all the plugs and doesnt miss... went to rev it up and it bounced of 2800rpm... At this time remembered my AFM was unpugged...

plugged in the afm i got from KYP.. it started running rich as a bitch and rather rough and would not rev above 3k, it didnt bounce it just refused to rev harder..

so better take the AFM back then.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • Thank you so much for the help
×
×
  • Create New...