Jump to content
SAU Community

Recommended Posts

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I've been off the road for the last 2 years but the car is finally registered (anyone needs easy rego, I found a great mechanic). Happy to bring out the R32 for show and shine. Probably no point on the dyno, most of the mods are drivetrain/clutch upgrades. Be a good chance to meet some of you.

I think I'm going to have to pull out, it's just too early for me...... :D

do-able if I can go home and just sleep after it's over, but I have Xmetal coming down to do a night shoot Saturday night and so I need to be running on more than a couple of hours sleep :D

We will stop in and have a look in the early arvo though...

Is this really all that are coming???

1. Bullet32 - Show 'n' Shine

2. Kat - Dyno comp and Show 'n' Shine

3. Bluprint - Show 'n' Shine

4. Ex!$t3nZ - Show 'n' Shine (ill be coming but my car will probably be parked with the toymods people)

5. Shell - Show 'n' Shine

6.dr 30 rsx shown shine dyno

Where would we like to meet beforehand? Haha if there's 5 of us and only 4 skylines not sure if this actually matters.

1. Bullet32 - Show 'n' Shine

2. Kat - Dyno comp and Show 'n' Shine

3. Bluprint - Show 'n' Shine

4. Ex!$t3nZ - Show 'n' Shine (ill be coming but my car will probably be parked with the toymods people)

5. Shell - Show 'n' Shine

6.dr 30 rsx shown shine dyno

7. MAG86 1984 MR30 Hatch - Show & Shine.

I propose to meet at the Woden Trash & Treasure and be rolling out at 0800

The canberra celica club is going to the same place too.

post-32896-1251969678_thumb.jpg

1. Bullet32 - Show 'n' Shine

2. Bluprint - Show 'n' Shine

3. Ex!$t3nZ - Show 'n' Shine (ill be coming but my car will probably be parked with the toymods people)

4. Shell - Show 'n' Shine

5.dr 30 rsx shown shine dyno

6. MAG86 1984 MR30 Hatch - Show & Shine.

Sorry guys I'm out! Having some issues at the moment.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...