Jump to content
SAU Community

Turbo Timer Setting Alarm Off?

GoodOldR32

By GoodOldR32,
in Car Audio & Electrical

 Share

Recommended Posts

Woo Hoo Apprentice

Woo Hoo

Posted
Posted
hi all, ive recently bought a Greddy turbo timer and had it installed, but now everytime i lock my car with the remote it sets my alarm off about 2mins later?? any idea on how to fix it???

Thanks.

mine did that i held the remote on for 30 secs once the engine was off, then to reset it held it down for about 10 secs while its running on the timer.

Link to comment
https://www.sau.com.au/forums/topic/281963-turbo-timer-setting-alarm-off/
Share on other sites
GoodOldR32 Apprentice

GoodOldR32

Posted
  • Author
Posted (edited)

hi all, ive recently bought a Greddy turbo timer and had it installed, but now everytime i lock my car with the remote it sets my alarm off about 2mins later?? any idea on how to fix it???

Thanks.

EDIT: also i dont know if its a stock or aftermarket alarm, i couldnt see any aftermarket system in there, my alarm will auto ARM after about 2mins once i take the key off ACC but it doesnt lock, if i hop out and press the button befor it auto arms it will lock the doors and arm it, if im inside and try to start it when its armed it will go off,

ive tryed to lock the car wile the turbo timer is runner but it doesnt (i didnt think it would lol) but i can lock the door with the key, then it will self arm and set the alarm off again...also even if the turbo timer is off befor i turn the car off it will still set the alarm off, the only way i can stop it going off is to disconnect the timer..

Edited by GoodOldR32
GoodOldR32 Apprentice

GoodOldR32

Posted
  • Author
Posted
mine did that i held the remote on for 30 secs once the engine was off, then to reset it held it down for about 10 secs while its running on the timer.

ive tryed holding the remote button down but after 10secs it turns the alarm on, the remote has 2 buttons, a big one and a little 1, i hold the little 1 down for 30secs and the indicators flash but it doesnt lock the car, it just changes it so now it doesnt auto lock, the only way i can stop my alarm going off now is just to lock it with the key, but that means the alarm doesnt arm... :):happy:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      Forced Performance Hta Turbos

      By Komdotkom · Posted

      Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • MBS206
      Stagea obd II low voltage

      By MBS206 · Posted

      This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • MBS206
      Crank Motorsports Front Axles

      By MBS206 · Posted

      Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • MBS206
      NC MX5

      By MBS206 · Posted

      Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • Komdotkom
      Crank Motorsports Front Axles

      By Komdotkom · Posted

      I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...