Jump to content
SAU Community

Recommended Posts

Its off the dyno with a few small things to touch up with the tune.

I have a dyno sheet ill get a copy sent to my email so i can post it up.

She made 461.3 hp atw on 1.5 bar or there abouts,Falls over a bit after 6.5k hits 1.5 bar around that mark then falls off a little back to 1.35 bar.

Pretty happy to be honest 409.653 fbft.

Theres room for more hp i just need to get a few little things tweaked.

  • Replies 114
  • Created
  • Last Reply

Top Posters In This Topic

Cam gears turn up tuesday ill get them on and tidy up the tune a bit more should push a little bit more out of her for power cruise im so exited,The car is performing so well.Im just thrilled atm and you can t wipe the smile off my face.

Im still down to chop that wog this year at powercruise but i think ill have to becarefull of bill and his gt42r 26/30.

Just with cam gears on tonight testing a few things with inlet and exaust picked up 40hp mid-range and made the turbos come on quicker but still picked up more in the top end.

Pretty impressive,Tomorrow back to the dyno to finish it off,When i took it in todat made 461hp on 1.35 bar on 1 bar with cam gears adjusted made 442hp atws.On 1.35 bar made 480 hp atws.

Still a bit more turning to go yet.

Ill get a dyo sheet sent to my email and post it up tomorrow.

Heres my dyno prints from tonight befor and after cam gears with std cams,I made up to 490hp atws on 1 run but we backed it off for safty,Befor the cam gears made 461hp after the cam gears made 473 hp atws but i picked up 40 odd hps in the mid range.

Here are the print outs from todays fun.

Also i drove the car to brissy tonight and back,Basicaly i tried to drive the car ecconomicaly and it worked out with some testing 200kms on the dot took 20.3 lts to refill the tank back to the top so its looking around 10lts per 100 driving on the speed limit on the highway,Is that good fuel ecconmy for a rb26?

dyno3.jpg

dyno2.jpg

dyno1f.jpg

  • 2 weeks later...

Some pics of my car from random people from powercruise 25!!

All and all Was a awsome week end id like to say thank you to the guys who shared a shed all running nissan motors!Dean and Bill!

Also to John Barry aka athony who went out of his way to be cooking bitch for the week end!

Ant man im gunna have you transfer your car into my name so you can t sell it befor next powercruise man i tell ya!

This picture is my good mate in the army who flew down from darwin to spend the week end at powercruise25.Thanks luke!

img37251.jpg

My Wog racing mate Deano riding shotgun,Has a tuff as nails 26/30 vl that was chewing things up all week end!

post1782021283083667976.jpg

post1414691283077607155.jpg

genthumbs2.jpg

Thanks man!

BTW just went and saw brad picked up my dyno bill had a heart attack!!! regrouped asked brad about the footage for powercruise weekend!!! 45 gig of footage lol whos up for some splicing!!!

I wanna go threw it and see how many swear words are spoken! hahah.

BTW there is no more hosaka tunning factory stickers!!! they are all gone!!!!!! looks so much cleaner without those stickers.

Edited by Gtir-keiron

Yep thx simo and ven for peeling off my stickers!

Dude do a profile on your frickin car for god sake,Its awsome!

Basicaly just imagine the tomei catalog thrown at a 2.6 and you have simos car!

To be honest its the best sounding 2.8 or skyline i have ever heard,Thank paul red racing for that one i guess.

Simo do a run down on your car please!

Quick update.

Picked up Iwins washer bottle/oil catch tank last week end from johnbarry,will fit perfectly as it was made for a 33gtr.Have ordered the lines to plumb it all in.Still have some minor stuff to paint in my engine bay to finish my gtr off.

My problem is when i run out of things to do on my car i end up selling them ......I need a new project damn it!!

Edited by Gtir-keiron

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...