Jump to content
SAU Community

Recommended Posts

I took my car (NA manual JZA80 Supra) to the mechanics on Friday to get a clutch replacement.

Friday night I just drove it home, but on Saturday night I when to the beast club cruise (a good hour away from where I live). I was driving with mates so it was quite a spirited drive, nothing major or illegal, but it wasn't sedated driving either. That night I probably used a half tank of fuel and did over a 100k's.

I pop the hood today just to check the oil and notice that my air pod is completely disconnected. The piping that leads from the air pod to... I don't know what you call it, it's black plastic and leads into the engine block was just flapping loose. Even the black plastic piece that was connected to the block wasn't tightened.

So far the car still runs fine, but I'm wondering what potential damage have I done with my spirited drive last night? And besides never returning to that mechanic (do you even need to pull that piece off to do a clutch?) what can I do to at least prevent further damage?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/282564-help-air-pod-not-connected/
Share on other sites

I took my car (NA manual JZA80 Supra) to the mechanics on Friday to get a clutch replacement.

Friday night I just drove it home, but on Saturday night I when to the beast club cruise (a good hour away from where I live). I was driving with mates so it was quite a spirited drive, nothing major or illegal, but it wasn't sedated driving either. That night I probably used a half tank of fuel and did over a 100k's.

I pop the hood today just to check the oil and notice that my air pod is completely disconnected. The piping that leads from the air pod to... I don't know what you call it, it's black plastic and leads into the engine block was just flapping loose. Even the black plastic piece that was connected to the block wasn't tightened.

So far the car still runs fine, but I'm wondering what potential damage have I done with my spirited drive last night? And besides never returning to that mechanic (do you even need to pull that piece off to do a clutch?) what can I do to at least prevent further damage?

Cheers.

Gonna do a full oil and filter change. However I do recall late last night the car was idling strangely. It would idle fine for the most part, but then occasionally dip right down to like 500rpm and nearly stall before quickly jumping back up again.

This whole ordeal has got me very worried.

Got a good lawyer? HEKT1K prbbly knows one!

Less Seriously; takes pics of the unattached bits before restoring all to normal and check on performance & fuel consumpt'n.

Gear shift OK after clutch instal?

If it was disconnected when you were driving I highly doubt ur car would run with no air going past the afm..

Its Pod Filter > Intake Pipe (with afm) > Plenum > Head btw not block :rofl:

if for some reason ur car was running and it was not connected im amazed, if it was it cud of sucked in something.. potential damage...

and no u dont needa take off ur pod filter and intake pipe for a clutch install

does it run fine again?

and no u dont needa take off ur pod filter and intake pipe for a clutch install
You might, because the engine needs to tilt back to drop the gearbox.

But obviously if it has basically been running, then I doubt it was disconnected at the time of the "spirited drive".

You might, because the engine needs to tilt back to drop the gearbox.

But obviously if it has basically been running, then I doubt it was disconnected at the time of the "spirited drive".

I think you misunderstand. Essentially, everything was connected except the airpod. Which was only being held in there by the brackets.

The air was still being drawn in further up via the open pipe which was just before the AFM.

99% sure all jz based supra's are MAP sensored - including the older 1jz-gte's from the early twin turbos

so all you could have done is ingest some additional grit from the air into the motor causing some additional wear of the internals.

unless your ingested some large bits it should be negligable damage caused - if you are worried, best option would be a compression and leak down test to check on the motors health.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...