Jump to content
SAU Community

Wtb Laurel Windscreen!

toffy

By toffy,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Dan_J Veteran

Dan_J

Posted
Posted

well if u can get a dodgy rwc, u can get a sheet of perspex jigsaw it up 2 size nd bolt it in

bunnings have 1.5 metre sheets but your gonna need a 1.7m so see if they can order one in 2m or what not

got front ceffy windscreen replaced recently 4 $360 from o'brians but rear windscreens they dont have so its 1.6k for a rear one from nissan which means its best 2 find a rwc that will pass perspex

lol

NICKCEFFY Enthusiast

NICKCEFFY

Posted
Posted

they stopped making them about two to three months ago Toff :) , i've looking since i smashed mine before last round, there wasn't any known in stocks around australia new, just may have been some sitting in the back of a shop somewhere. I'm using the perspex version at the moment and its shit really, as soon as there is a little bit of dust on the screen and you wipe it it scratches etc

I'd be trying Nisswreck if anything.

toffy Veteran

toffy

Posted
  • Author
Posted (edited)

yeah perspex is no good :D , thought of that allready . funny you say that nick , everywhere i ring asks if i called them already lol . perhaps we should go halves in ordering genuine from melb? . theres more bits i need too btw guys , it's pretty urgent because i need a car to drive! (list below)

i need complete trim from dash up (roof lining, sun visors , side plastic moulds , jesus handles , rear parcel shelf etc , i don't care what colour ) and carpet , i will buy a complete trim if need be.

i'm also looking for a boot carpet , series 2 tail lights and and anything else anyone might have laying about for laurel . cheers

theres more i need , i'll update when i remember

Edited by toffy
toffy Veteran

toffy

Posted
  • Author
Posted (edited)
Nisswreck in adelaide are wrecking a C33 if you get completely desperate.

yeah cheers mate , i did ring them , and asked about everything except front window , might try again :D

i did hear that either s13 or s14 fit , but i don't have either to measure off :)

Edited by toffy
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...