Jump to content
SAU Community

Recommended Posts

Hi All,

The next SAU dyno day is to be held at SST on Sunday the 7th of December, and we'd like anyone from SilviaWA or any other jap import who wants to compete to join us. You will need to complete the form and pay $30 prior to the event to be eligible. We only have limited spaces so get in quick. We're expecting to kick it off at about 10:30. We'll be having a lunch break and will be running a sausage sizzle.

There will be trophies for Highest HP 2L, Highest HP 2.5L and Highest HP 2.6L or greater. There will alos be an exhibition class where we're hoping to have a few very high horsepower cars make an appearance:D

http://www.tnet.com.au/~dantheman/Shooutou...mniform-SST.doc

Link to comment
https://www.sau.com.au/forums/topic/28419-sauwa-dyno-comp-sun-dec-7th-sst/
Share on other sites

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

If you have sent you money and form in and your not on this list then PM me:D

Entrants:

Luv DR

Shuto-boy

REP003

MearCat

Jill200SX (SilviaWA)

Yoon Kang

DSTURBD

living backwards

Gavin (japSpec)

B_real (SilviaWA)

ND4SPD

jmp

Bully?

S13 Angel

DR30RS

I will not be running.

I just got a new clutch installed today, canna flog it for a short while....bugga!!!

Also I will come down to support and I will even pay $10 for steve to show me how to adjust my friggin bleed valve (sounds like a bit much, but thats how much I wanna support)

heck I dont mind still paying that $30 if steve will do me a power run later in the week or when I can clock up enough k's on the new clutch

i got sunburnt :cheers:

good to catch up witha few peeps ....... stoopid sun burn tho :(

Thanks for cooking the snaggers Cam ..... big thank you to SST and Paul for organising and the people that came down and supported the event :grouphug:

No probs Niz - farkin hot job it was. I saw quite a bit of sun myself.

Good work by both the postwhore and the SST boys. And thanks to all those who came along.

Paul - you going to post up a full set of results?

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...