Jump to content
SAU Community

Recommended Posts

  • Replies 93
  • Created
  • Last Reply

Top Posters In This Topic

Ummm, mine.

Lags a bit at the top end so need to upgrade the coil packs

Hicas comes on and feels weird so I need a lock out bar

The pwer wondows rattle a lil bit and may need to have the windows re tinted

The nuff nuff paid to put the 400R body kit on did a messy job on the wheel arches, need fibre vision to look at fixing them up. See them tomorrow.

Oh yeah, and had to settle on my 2nd choice for personal plates becaue BLINKY was already taken... (see previous thread for more info)

Other than that I am happy.

Blinky

problems with the three two

~4 stud

~clutch is crap

~gearbox is crap

~brake master cylinder cracked a seal and is now leaking

~ripped bushes in stock castor rods

~water getting inside the boot

~you cant wind the passenger side window up with the passenger side button but driver has complete control of it

~shift knob is crap

~aircon climate control is being crap

~and last but not least ITS NON TURBO AAAAAAHHHHHHHHHHHHH!!!!!!!

Hmmm....

- Missfire under boost (Coilpacks need replacing)

- Side tinting needs re-doing as there are these two annoying visible lines

- Wheels haven't arrived yet

- Paint/body needs freshening up

- Eclipse satnav/cd player is shizen

- Brakes occassionally squeaky

- Front bar ever so slightly not fitting right due to my gay driveway

- Right headlight is yellow

Thats about it. I was happy a little while ago...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...