Jump to content
SAU Community

Tiptronic/mm Question

Easy Tiger
 Share

Recommended Posts

Easy Tiger Enthusiast

Easy Tiger

Posted
Posted

I remember reading in a thread not long ago someone saying you shouldn't keep the accelerator depressed when shifting gears on the auto in the tiptronic/manual mode. The rationale was that you wouldn't keep the accelerator pedal depressed when changing gears in a manual, so why would you in manual/tiptronic mode?

I was trawling G35driver.com today and came across a thread about it, which says that you should keep the pedal depressed while changing gears in tiptronic. To me this makes more sense, as even if in manual mode, it is still an automatic gearbox and all you are doing is telling the car when to change gears, rather than it choosing for you. If you're not dropping revs into it from neutral or redlining it then I don't see how it can be doing any damage as it is still running the same auto mechanics.

Anyone else agree?

Here is the link: http://g35driver.com/forums/engine-drivetr...ronic-tips.html

Link to comment
https://www.sau.com.au/forums/topic/285856-tiptronicmm-question/
Share on other sites
GoldV35 Enthusiast

GoldV35

Posted
Posted

Come on, own up to it, who thinks that you need to let off the accelerator when selecting a gear in a tiptronic AUTOMATIC gearbox? Then what do you do after letting off the accelerator, push the clutch pedal in? hahahah

n15m0 Grand Master

n15m0

Posted
Posted

I believe the words of wisdom came from here:

My preference is for a CVT gearbox as in normal bumper-to-bumper driving and highway cruising, the CVT changes gears smoothly at under 2,000 rpms in DRIVE gear = fuel economy. But when u slap it into tiptronic mode, it changes it characteristics and can rev to almost redline....just make sure that when u do use the tiptronic, to let your foot off the accelerator, change gear, then step on the accelerator...This 'TIP' is for those who have come from a manual transmission setup....You wouldn't change gears without clutching; would u? So please, despite the way how many drive tiptronics (like Top Gear), if u wanna prolong your auto transmission, ease off the gas b4 u change gears...Obviously this doesnt apply when u r in the DRIVE gear...

My 2 cents worth anyway....

scathing Grand Master

scathing

Posted
Posted

If you're driving a car with a torque converter gearbox you shouldn't need to lift. It doesn't matter whether the electronics think its time to change or you do, in the end the mechanical process to select a new gear is the same.

I am pretty sure that advice should only apply to gearboxes with clutches. Whether you've got a 3 pedal setup, or you've got a car with an electronically controlled clutch (BMW SMG, Ferrari F1, VAG DSG, etc) its good to lift off the throttle when it changes gear and be gentler on the driveline.

The problem is that a lot of people drive the latter like a slusho because its only got 2 pedals, but mechanically it behaves the same as a traditional manual.

Timmi Explorer

Timmi

Posted
Posted
If you're driving a car with a torque converter gearbox you shouldn't need to lift. It doesn't matter whether the electronics think its time to change or you do, in the end the mechanical process to select a new gear is the same.

I am pretty sure that advice should only apply to gearboxes with clutches. Whether you've got a 3 pedal setup, or you've got a car with an electronically controlled clutch (BMW SMG, Ferrari F1, VAG DSG, etc) its good to lift off the throttle when it changes gear and be gentler on the driveline.

The problem is that a lot of people drive the latter like a slusho because its only got 2 pedals, but mechanically it behaves the same as a traditional manual.

Ok officially confused... all different replies....

say you want to get a good run off the line, shifting at red zone...

cause i tried changing to 2nd with my foot down on the pedal... car just ignored me and bounced all the way to limiter XD.... refused to change gears.....

is it some kind of self-protection?

so im guessing it should be like this? correct me if im misunderstanding..

1)TDC off...

2)hold brakes and rev to 1.5-2k

lights change

3) pedal to metal on M1

4) lift/ease off gas to change to M2 ?????

5) stomp on gas again???? or ease back in????? (VDC off)

V35_Paul Veteran

V35_Paul

Posted
Posted

Keep your foot down the whole time. Change the gear 500rpm before the red line. The gear changes are slower then you change and needs a little time.

If you wait until you get to the red line you'll hit the limiter.

Or get some grounding wires that should help. Right?

Easy Tiger Enthusiast

Easy Tiger

Posted
  • Author
Posted
another question guys.

Does the power button will do anything on Manual shift?

Don't think so. All it does is hold the lower gears longer when accelerating hard and jump down gears quicker when you plant the right foot in auto mode. With manual mode you control this yourself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...