Jump to content
SAU Community

Recommended Posts

Firstly check VIN # > History of where it was owned. If it came from anywhere on the north island of Hokkaido (ie names like Kushiro, Sapporo, Hakodate, Asahikawa, Muroran etc) the chances of rust are huge.

Where? As mad082 said^^^, and also struts, rails, door hinges, wheel well...

there is one more spot. dont forget to look around the boot brake light, it can get rust around there, mine has a little bit atm.

That is indeed the most common arear for rust. I've seen a lot of new imports with rust just below the brake lens, including my old GTT.

  • 3 months later...

It is very common - but not something to worry about because it's one area where the rust is quite visible; and thus, most people attend to it quickly.

After washing the car, you'll notice that water likes to sit beneath the lens; so it pays to soak it up.

After it's fixed, it won't tend to recur under Australian conditions because in Japan, where there's salt in coastal areas, salting of roads in Hokkaido, SO2 & SO3 gasses (emitted by lots of cars in crowded cities where many drivers don't drive very far) which mixed with moist air > H2SO4 (sulphuric acid).

It is very common - but not something to worry about because it's one area where the rust is quite visible; and thus, most people attend to it quickly.

After washing the car, you'll notice that water likes to sit beneath the lens; so it pays to soak it up.

After it's fixed, it won't tend to recur under Australian conditions because in Japan, where there's salt in coastal areas, salting of roads in Hokkaido, SO2 & SO3 gasses (emitted by lots of cars in crowded cities where many drivers don't drive very far) which mixed with moist air > H2SO4 (sulphuric acid).

Cheers Terry, thanks for the fast response and clarification! ;) Any other known potential rust trouble spots that should be checked apart from around the spoiler base and around the windows?

Thanks again mate!

Edited by KR4-GTR

The most common area I see from freshly imported cars into our workshop is the underbody. Mostly it's light surface rust from the salt used in snow regions which can be removed. But on some occassions I see quite substantial rust which obviously is a lot more difficult to remove.

Those salty roads are the pits.

Talking on Nissan 4x4 forum to a guy in Ireland who bought a low mileage 2nd hand Patrol but she's got an engine oil leak.

Turned out the sump has rusted through.

Piece of foam material between bellhousing and sump had absorbed the brine and rusted right through the sump.

Wondering about the rest of the underbody?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...