Jump to content
SAU Community

Recommended Posts

Recently got some 2nd hand Volk te37s, got them balanced and after they were put on got all of the wheels aligned, and was told I have slightly negative camber in the front...(dunno if this is whats doing it...). They are 18 x 8.5 fronts and 18 x 9.5 rears on an R34. The back tires came with the rims and are chewed up pretty bad, fronts are fine.

I put them on my car and went for a cruise and noticed that my car seems to get stuck in ruts on the road and swerve from left to right or right to left on the road in these ruts sort of thing, like its always swerving both ways by itself.... Never did this before on my stock rims and never heard of a car doing this :S

Anybody had this experienced and fixed it, or know whats going on? I have no idea! Any help's appreciated.

Plan on getting new back tires to see if that'll fix it but I doubt it will, so if anyone can shed some light, I'd be forever greatful, thanks!

- Jack

Link to comment
https://www.sau.com.au/forums/topic/286837-new-rimsnew-problem/
Share on other sites

Also, it used to be that radial tyres got used to rotating primarily in one particular direction. If you then swap sides with them, so they rotate primarily in the opposite direction, the belts go all funny and you get symptoms of a bad alignment.

It isn't a GTR. Before you have a crack at grammatical errors, check the time I posted it; tired!

I've taken it to tyre shops tired to explain they just blame alignment or balancing....I need to get them to drive it to make them understand. Its like its getting stuck in ruts and swerves both left and right...

I'm getting new back tyres this week although I doubt this will solve the problem due to the fronts being the ones that actually steer. When I get the tyres I'll ask them to check the toe elk, dunno what it is though :woot: and make sure the air pressure is correct... I'll let you know how it goes, cheers guys!!

Get a wheel alignment and see if it's still there. I know the feeling and it can be because of the larger scrub radius of using wheels with less than stock offset. Alignment should help a lot. More caster will also help a lot so consider a whiteline caster kit or similar.

Check your shockys..

I had a slight tracking problem with roadruts, liked to follow camber a bit to keenly especialy to the left , had a front and rear wheel align nothing realy out but ($60 flung out).

Got a slight clink at slow speeds on little bumps on passenger side took it in for a check, turns out I had a blown nearside front shocky so ($45 flung out) replaced it myself ($205.57 invested), no more tracking drives lovely.

Decided to check the rears myself on a whim (no $) and---fric my old boots---drivers side rear seeping, obviously for a fair period of time, replaced myself ($173.01 invested) drives even lovelier.

R34GTT on Nexen 225x45x17.

:woot:

sounds just like tramlining. get them to check all the settings against stock. if OK, and there are no obvious issues with dampers or worn / loose components then a really good suspension place could try and dial it out to some extent with different settings, and tyres with harder sidewalls will help but IMHO there isn't much you can do about it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...