Jump to content
SAU Community

Recommended Posts

Thanks for sharing Fineline, appreciated.

So how much ballpark for JHH to do your porting and lifter conversion. I see you didnt go for a huge cam, so was it necessary to go solid lifters ?

Gary

The actual solid conversion only cost about 600 dollars from memory Gary.

My cam selection was based on the type of power delivery I was looking for. Pon cams are not big but they are bigger than anything I could get in the 25 hydraulic lifter set up.

port work depends on how deep your pockets are. I was fortunate in that the original head I purchased had 80% of the porting and chamber work already done. JHH touched up the inlet side When they fitted the o/s valves springs etc.

The head still wasnt where we wanted it as far as the exhaust side went so I gave it to Mik at signature and he weaved his magic on it. He has dossiers as thick as encyclopedias on eons of intensive porting and flowbench work on RB heads, I am not at liberty to give away too much but suffice to say the head flows beautifully.

Our cam timing is a little different to what some may consider the norm but the results speak for themselves. I see my first lb of boost at only 1600 rpm and it just hoses hard all the way to 8 kay. Whilst I am pleased with the end power figure it is secondary to the power delivery This engine dishes out. That was my primary goal right from the getgo and it has delivered in spades.

Given my time over I could do it in half the time and half the cost. There was so much trial and error involved. The first engine did over 350 power runs on the dyno mainly due to my own stubbornness in refusing to believe some of my ideas wouldnt work. Dan built that engine as well, It was a gem but alas it came to grief when the clutch nuked and ripped it apart.

Best tip I can give anybody wanting to do this sort of thing is simply, Do not take one shorcut. Not one. These boosted engines have a way of seeking out the weakest link and destroying it, Usually taking other compenents along for the ride.

  • 4 weeks later...
  • Replies 112
  • Created
  • Last Reply

Top Posters In This Topic

Hi Fine Line , thats my theory as well with my RB25 - so much tied up in the head . My modified head isn't on yet and it has OS exhaust valves as in larger but not enough to need the seats to be changed . For cost reasons I stayed hydraulic and got R33 RB25 poncams for it . With skimming the CR should rise to a bit over 9:1 .

The exhaust manifold I'm thinking of running is the cast HKS one and hanging a GT3076R off that . My goal is to have a very streetable 280+ Kw and if keen enough may get RIPS modded lower inlet manifold and mount RB26 multi throttles on it for snappy throttle response .

It's the torque and response I'd like in a reasonably free reving RB25 .

Cheers A .

9k on a real good head is not over the top for the right engine, we spend alot more than that to build our top of the line heads and I can confirm big power comes pretty easy with the right headwork and everything else "just right".

nzd60-80k is pretty easy to spend on a real nice complete 1000-1400hp+hp RB30 with all the good gear.

Rob

We.re not trying to run 7 second passes ripmeister. responsive strteet/track car is where its at for me. but yeah, I have spent a good deal on head work and flow. It makes sense to make the power i want without having to turn the boost wick up any more than i want to.

well the intake side was match ported to the runners and exhaust side has been ported and polised. im still running standard cams but plan to get something bigger when the cash flow is a bit better.

Valve springs and valves are still stock but that should be fine unless im going for 1000+hp right?

T/B is port matched to the plenum is port matched to the head is port matched to the exhaust manifold is port matched to the turbo is port matched to the dump and so on down the line.

im currently just running the standard GTR plenum. im not sure how big these things are but im pretty certain ill have to be upgrading this aswell along with the TB.

exactly how big have you match ported everything FineLine?

any thoughts?

you'll more than likely encounter valve float with the std springs. get some aftermarket springs put in when u get the cams (some psi springs should be fine, about 300)

thanks for the tip shanef......its like someone else on SAU said....theres always something stopping me lol

Edited by Jap_Muscle
im currently just running the standard GTR plenum. im not sure how big these things are but im pretty certain ill have to be upgrading this aswell along with the TB.

exactly how big have you match ported everything FineLine?

any thoughts?

thanks for the tip shanef......its like someone else on SAU said....theres always something stopping me lol

with fineline's setup (i've spannered on it many a time :banana:) the plenum and manifold are matched to the size of the ports in the head. his head having been ported by a cylinder head shop, is very different to the std or even a 'rough hand make the ports bigger job', so just port match them to the shape of the ports in the head.

with fineline's setup (i've spannered on it many a time :banana: ) the plenum and manifold are matched to the size of the ports in the head. his head having been ported by a cylinder head shop, is very different to the std or even a 'rough hand make the ports bigger job', so just port match them to the shape of the ports in the head.

would it be fair to say it be cheaper just buying a aftermarket plenum? or having one custom made by Hypertune to the port sizes?

ur misunderstanding it...

any manifold you buy, even the std one, wont have the same shape in the port where it bolts to the head. By making the plenum (or manifold) port the same shape as the port in the head, this is called 'port matching'.

You wont need a new plenum for your goal.

Gotta say that valve springs are a good investment.. valve float is going to be the killer.. Agreed with Shane :banana:

I made more power on my built 25 (still has the 25 bottom end) with poncams (baby type A's) and Type A springs than dave made on his built 26 with same poncam equivalent and standard springs!! This was on the T04Z thought not the GT35R... same turbo two different cars, and same engine builder! - I stole his turbo whilst he wasn't looking :blink: Annnd my fuel setup isn't as sorted as his.

He got to 376rwkw before no matter how much boost they dialled in, it just wouldn't make any more power due to the valve float.

My Gt35r only had the 0.63 rear and the exhaust was 3" with a metalcat and one muffler - but this ended up being the restriction and I couldn't get past 350rwkw... not sure if the smaller rear had anymore in it though??? This was on 21-22psi too...

post-30020-1255353855_thumb.jpg

Can't see why it wouldn't get to near 400rwkw on pump with the right setup :D

interesting....i might just have to invest in some valve springs then.

how much do they go for these days? does SAU have any traders who sell? recommended brand type or seller at all?

btw msnismo, what sort of cam system are you running?

edit::

what is the difference in Type A B and C valve springs? are they similar like Cams where power is made at different points throughout the rev range?

sorry guys im a complete freshmen when it comes to engines.

Edited by Jap_Muscle
interesting....i might just have to invest in some valve springs then.

how much do they go for these days? does SAU have any traders who sell? recommended brand type or seller at all?

btw msnismo, what sort of cam system are you running?

Just tomei 256 in/ex... smallest ones out! I didn't want to go solid lifters as I wanted my car back by that stage! Dave did do a little porting on the head/valves etc but not a great deal. The springs are just tomei Type A's... I picked mine up a while ago for $450 odd new.

And no cam gears... I was told the poncams run best on standard as that is how they are designed and tested.

Edit:

Type A cams need type A springs for optimum result or can use standard to a certain point (a drop in replacement, no mods needed)

Type B cams need type B springs for optimum result

etc etc... Some I think you have to run the springs, once you get to a certain level then its lifters and everything - well on a 25 head anyways!

how much power did you make with the gt35r msnismo? did you just simply swap the turbos or did you do other mods? also what rear housing did you use on the 35r?

i know with a t05z 400kw isnt a big strech at all and it is able to make that sort of power without all the added strings attached. alot of VLs, Skylines and among other cars are pushing 400+ kw out of a .86 gt35r.....and i would much like to do the same before i step up to something bigger.

i just wish i knew wat was missing. i do however have added valve springs to the list of things to do.

as it stands now....some cams/cam gears, valve springs, and 25+psi should be a good place to start.

as i mentioned before the car is currently sitting at 330kw on 16psi which is a great effort i guess, but the turbo is no where near its efficiency range.

a small snapshot of the progress thus far. it does need a good polish though

img0129d.jpg

Edited by Jap_Muscle

GT35R - 0.63 rear - exhaust was 3" - 6 boost manifold

The dyno sheet is in my post - 345rwkw.. it wanted to make more power but the exhaust said NO... changed turbos as the T04Z power delivery is much more fun :D annnnnd it was just lying around :banana:

By Comparison, I had 330rwkw at 15psi on my GT35R....

T04Z is 0.84 rear - exhaust 3.5" and cat free :blink: - more in the turbo, just not my fuel set up!

EDIT - Sorry only change between turbos was - larger exhaust and more free flowing, and a custom 1" steampipe manifold to avoid some lag (similar to my old 6 boost) . .... rest of setup remained exactly the same

You don't need bigger than a GTR plenum for 400rwkw.

There are plenty of cars from Racepace that have all gone 380-400rwkw without altering anything from factory plenum/intake wise.

They all run factory cam's are well incidentally.

GT35R - 0.63 rear - exhaust was 3" - 6 boost manifold

The dyno sheet is in my post - 345rwkw.. it wanted to make more power but the exhaust said NO... changed turbos as the T04Z power delivery is much more fun :D annnnnd it was just lying around ;)

By Comparison, I had 330rwkw at 15psi on my GT35R....

T04Z is 0.84 rear - exhaust 3.5" and cat free :D - more in the turbo, just not my fuel set up!

EDIT - Sorry only change between turbos was - larger exhaust and more free flowing, and a custom 1" steampipe manifold to avoid some lag (similar to my old 6 boost) . .... rest of setup remained exactly the same

my rb26, gt35r, 1 inch 6boost manifold, .82 rear housing, 3 inch exhaust, standard cams and springs set-up makes 330rwkw on 23psi, thought i was the only one with that manifold, guess not.

how do you guys control boost with those sort of setups? wastegate mounted off the exhaust housing?

i changed from a .82 to 1.06 (havent yet retuned) and added a bigger gate (44 to 48mm) and it started to boost creep madly from there.

i had a similar problem.

the rb30 along with a 6boost manifold was just flowing so much air that the 44mm gate wasnt expelling the air fast enough to control boost. had the 6boost manifold modified to fit a 60mm gate.

that dosnt just mean slapping on a 60mm gate. you have to make sure the pipe that leads to the 60mm gate is 60mm aswell. havnt tried anything smaller but the 60mm fixed my issues.

i had the .82 rear

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...