Jump to content
SAU Community

Gt35r Install Help

jdmtom

By jdmtom,
in Engines & Forced Induction

 Share

Recommended Posts

jdmtom Apprentice

jdmtom

Posted
Posted

I have just purchased the Full Race manifold for the rb26dett and a GT35R with twin tial wastegates. Does anyone have any Single turbo install writeups. What is the best choice for fuel pumps. Every one here one the East Coast (usa) is recomending walboro 255 intank and a external bosch. Without poping the head what is the maximum amount of Boost a stock 26 can take safely every day. I have 1000cc T1R injectors, D-jetro Power FC and a tune is coming when the install is completed. Does anyone have any part numbers for the water and oil lines as well as the plugs.

Thanx for all the help.

Tom

Link to comment
https://www.sau.com.au/forums/topic/287619-gt35r-install-help/
Share on other sites
NYTSKY Grand Master

NYTSKY

Posted
Posted

As for the turbo install,

Pull everything off

Replace manifold studs

Put on the manifold and turbo so you can fab the lines.

Fab dump and wastegate pipes

Fab vacuum lines

Fab intake.

Done, i assume you have all new gaskets too.

Id use a Bosch intank and a Bosch external (maybe two)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Dose Pipe Sutututu
      Blue slip

      By Dose Pipe Sutututu · Posted

      Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Stringycheese
      Blue slip

      By Stringycheese · Posted

      Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • Duncan
      Blue slip

      By Duncan · Posted

      You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • Duncan
      Ethanol Content Sensor - Always at 11%?

      By Duncan · Posted

      yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...