Jump to content
SAU Community

R34 Gtr New Key Coding To Nats System

BookyVL

By BookyVL,
in Car Audio & Electrical

 Share

Recommended Posts

33GTRV Mentor

33GTRV

Posted
Posted

Key cutting is a given-Locksmiths do this for a living. As for the Programming of the NATS key, there are 2 options.

Option 1: Take the key(already cut and ready to go) to your preffered nissan dealership and ask the people there nicely to Program your key to your car, its a 2 min job with a consult system

Option 2: Now this is the tricky bit. It sounds easy and looks easy but its sometimes a pain in the ass if you arent fast enough. There is a simple set of Functions the car can use to recognise you are programming a ke as a secondary option. To do this you will need to:

Here they are....... enjoy!!

ID Code Entry Procedure

To enter the ID code, follow this procedure:

"Setting Mode":

1. Close and lock all doors.

2. Insert and remove the key from the ignition more than six times within 10 seconds. (The hazard warning lamp will flash twice). At this time, the original ID codes are eliminated.

ID Code Entry:

3. Turn ignition key to "ACC" position

4. Push the "lock" button on the new remote control once(for example, if the door is locked using the remote controller during this ID code entry state, a new ID code can be entered). At this time, the new ID code is entered. (The hazard warning lamp will then flash twice).

Additional ID code Entry:

5. If you need to activate additional remote control units, unlock the drivers door, then lock it again(WITH THE DOOR LOCK SWITCH).

6. Push the lock button on the additional remote once.

7. This ID code enable state and setting mode will remain until the drivers door is opened.

NOTE!!

* If you need to activate more than two additional keyless remotes, repeat the procedure "Additional ID code entry" for each new remote.

* If the same ID code that exists in the memory is input, the hazard warning lamps will flash twice but the entry will be ignored.

*Entry of a maximum of four ID codes is allowed and any attempt to enter more will be ignored.

*Any ID codes entered after termination of the "Setting Mode" will not be accepted. Additional keyless remote signals will be inhibited when an ID code has not been entered during the setting mode.

*Some cars that were imported also had a NATS2 system that was varied to the normal Nats. You cant manually program these keys and will need to Take it to a Nissan Dealership to be Programmed with the CONSULT2 system. This may take up to 20 mins and therefore you may be charged a half hour block of labour.

Good Luck and hope this helps!! Might even get a sticky :P

  • 3 weeks later...
aphid Proficient

aphid

Posted
Posted

what if your key doesn't have the remote central locking button? My key is just the standard r34 gtr item

with the logo but no remote central buttons :P

does this mean I need to take it to Nissan to get programmed? Is it possible to program through a laptop via a consult cable??

Thanks ;)

On a side note, Dont go telling the whole world how to do it, there is bound to be some kid in an N13 pulsar that will lock himself out of the Nats ecu lol
FelixTRX Community Regular

FelixTRX

Posted
Posted

Just slightly to the left of this topic, I have a 1999 Nissan Elgrand, it only came with 1 factory key, so we want to get 2 more keys cut. I was told by my alarm installer that I have some kind of key ID ring on my ignition barrel. He said that I have to get factory Nissan keys (not cheap) instead of the normal metal keys that we had with our 1997 Stagea.

Has anybody got around this?

Cheers, Greg.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

so it has NATS2.8 on it? never seen one with that system there. the keyless side of things yes. never NATS though. is there a blue or red square at the base of the key?

EJD001 Mentor

EJD001

Posted
Posted

Could anyone supply a part number or price for the key in post 10? Im keen on getting a second remote key.. but was told by nissan that it was going to be 330+gst and they couldnt tell me if it was the correct key!

FelixTRX Community Regular

FelixTRX

Posted
Posted

Well Chris, the collar around my ignition barrel is the light, nothing more, nothing less! My mate who installed the alarm must have it confused with something similar to what he sees on newer Nissans!

post-22822-1254712881_thumb.jpg

post-22822-1254712916_thumb.jpg

I have another question regarding stereo wiring but I'll start a new thread for that!

Cheers, Greg.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted
Could anyone supply a part number or price for the key in post 10? Im keen on getting a second remote key.. but was told by nissan that it was going to be 330+gst and they couldnt tell me if it was the correct key!

that is the correct price.. they are NOT cheap.

got a chassis number and I'll look it up for you.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted
Well Chris, the collar around my ignition barrel is the light, nothing more, nothing less! My mate who installed the alarm must have it confused with something similar to what he sees on newer Nissans!

post-22822-1254712881_thumb.jpg

post-22822-1254712916_thumb.jpg

yep thats the plain barrel. the NATS one looks entirely different.

EJD001 Mentor

EJD001

Posted
Posted

I had the same problem whe i got my car.. went to nissan and got a normal steel/ metal key.. got it cut and it does the same job.. except it doesnt have the remote entry to gain access to the vehicle!

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted
what if your key doesn't have the remote central locking button? My key is just the standard r34 gtr item

with the logo but no remote central buttons :thumbsup:

does this mean I need to take it to Nissan to get programmed? Is it possible to program through a laptop via a consult cable??

Thanks :(

I know what your trying to do....you have the key with the red bit yeah?(transponder in there....)Im guessing you want to do that and not the central locking key fob....You maybe able to find a locksmith that has a tool to read your key and program the new key.....I posted the info for the fob quite some time ago here key fob....on another note you can also buy the fob from a nissan dealer and code it even if you dont have one

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Crank Motorsports Front Axles

      By MBS206 · Posted

      Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • MBS206
      NC MX5

      By MBS206 · Posted

      Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • Komdotkom
      Crank Motorsports Front Axles

      By Komdotkom · Posted

      I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
    • Josh K.
      Crank Motorsports Front Axles

      By Josh K. · Posted

      Had I known the diff between R32 and R33 suspension I would have R33 suspension. That ship has sailed so I'm doing my best to replicate a drop spindle without spending $4k on a Billet one.
    • Josh K.
      Crank Motorsports Front Axles

      By Josh K. · Posted

      OEM suspension starts to bind as soon as the car gets away from stock height. I locked in the caster and camber before cutting off the kingpin. I then let the upright down in a natural (unbound) state before re-attaching it. Now it moves freely in bump and droop relative to the new ride height. My plan is to add GKTech arms before the car is finished so I can dial camber and caster further. It will be fine. This isn't rocket science. Caster looks good, camber is good, upper arm doesn't cause crazy gain and it is now closer to the stock angle and bump steer checks out. Send it.
×
×
  • Create New...