Jump to content
SAU Community

Resestting ECU

ex-static

By ex-static,
in Engines & Forced Induction

 Share

Recommended Posts

DAMQIK GTS-T Community Regular

DAMQIK GTS-T

Posted
Posted

p.s I dont like getting into the kick pannel were the ecu is as I belive the more one root's arround with it the more likely some of those fine wires will break in the socket.

The less you remove the ecu the better.

Note it would be quite costly to replace the scoket that plugs to the ecu. It could also cause faults that are hard to trace.

Thats why I think its better to reset the ecu the paper clip way.

my 2 cents

DAMQIK

_turtle_ Proficient

_turtle_

Posted
Posted

just tried the paper clip method. it worked!! realised i was putting it in the wrong holes wen DAMQIK said that the points had wires going into them. i was putting the clip into 2 empty ones hehe.

the engine check lite flashed 5 times slow, and then 5 times quick? and then just kept repeating itself after that. anyone know what that means?

  • 2 years later...
R31Heaven Proficient

R31Heaven

Posted
Posted

I know this is digging up an old thread, but I thought the paper clip trick only reset the diagnostics (this needs to be done after replacing a faulty componant) mode not the actual ECU (learning). Droppng power to it and draining off any power by pressing the brake or leaving over night is the only way I know..

  • 3 months later...
  • 3 weeks later...
caz Enthusiast

caz

Posted
Posted

Hey guys, the diagnostic tool you need isnt expensive! and you can share it with any mates that have a pre 97 Nissan with the grey consult diagnostic port. If you have a laptop ,USB ECU Interface cable and software can cost as little as $155.

If you are interested, check out my ad in the 'for sale from our sponsors' .

Im quite happy for you to borrow mine too if you are Sydney based.

Cheers,

Caz... :D

I really don't think it would have done too much.....the proper diagnostic tool is needed and after the reset there are certain driving processes it needs to help the computer 'learn'.

caz Enthusiast

caz

Posted
Posted

CODE 13 is Engine coolant temp sensor, very common fault. Remove and clean the connector with a tiny file and contact cleaner, retension the insides so they connect well, clear the fault from your ecu , replug and try again!

ECU SELF-DIAGNOSTIC ERRORCODES

Code 11* :

Camshaft Angle Sensor circuit (CAS)

Either 1° or 120° signal is not entered for the first few seconds of engine cranking,

Either 1° or 120° signal is not input often enough while the engine speed is higher then the specified RPM.

Check harness and connector (if harness and connector are OK, replace CAS)

Code 12 :

Air Flow Meter circuit (AFM)

The AFM sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector (if harness and connector are OK, replace AFM)

Code 13 :

Engine Coolant Temp. Sensor

The Engine Coolant Temp. Sensor circuit is open or shorted (abnormal voltage is registered).

Check harness and connector of Engine Coolant Temperature sensor

Code 14 :

Speed Sensor circuit

The Speed Sensor circuit is open or shorted.

Check harness and connector speed sensor switch (reed switch)

Code 21*

Ignition signal circuit

The ignition signal in the primary circuit is not entered during engine cranking or running.

Check harness and connector of the Power Transistor Unit

Code 26

Boost Pressure sensor (Turbo models)

The boost pressure sensor is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check for boost pressure leaks, check boost pressure sensor

Code 31

Control Unit

ECU calculation function is failing Replace ECU

Code 32

EGR function

EGR valve does not operate (valve spring does not lift)

Check EGR valve and EGR-solenoid

Code 33

O2 Sensor (left side)

The O2 Sensor is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, O2 sensor, Fuel pressure, Injectors, Intake air leaks

Code 34

Detonation Sensor circuit

The detonation sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check Harness and connector, detonation sensor

Code 35

EGR Temp. Sensor

The EGR Temp. Sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check EGR temp. sensor

Code 42

Fuel Temp Sensor circuit

The Fuel Temp. Sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check Fuel temp. sensor

Code 43

Throttle Position Sensor circuit

The Throttle Position Sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check throttle position sensor

Code 45

Injector leak

Fuel leaks from the injectors Injectors

Code 51

Injector circuit

The injector circuit is open

Check harness and connector, check injectors

Code 53

O2 Sensor (right side)

The O2 Sensor is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, O2 sensor, fuel pressure, injectors, intake air leaks

Code 54

Signal circuit from the automatic transmission (A/T) (A/T models only)

The A/T communication line is open or shorted

Check harness and connector

Hope this helps,

Cheers, Caz... :D

can someone please post what all the codes are? i cant find it, and me mates has just started flashing code 13.

  • 7 months later...
GTAAAH Mentor

GTAAAH

Posted
Posted (edited)

absurdely old topic and all but, the above list of problems do you need the ecu diagnostic tester to assess? or is there like a LCD screen in the ecu that gives u codes or a LED

thx itd save me asking alot of questions if i could get these codes goin. That and i dont like pulling kick panels apart and going near old wiring if i dont have to

Edited by r32 gts-turbo
  • 1 year later...
  • 2 months later...
Nick033 Experienced

Nick033

Posted
Posted

i know this may seems as a bit of a noob qs but is there any harzards involved with resetting the ecu???

i recently had a faulty afm which i fixed by resoldering the three pins inside on the circuit board, i was getting stalling and hesistation problems all the time and the car chewwed fuel like no tommorow, but the car still seems to run a little rough around the 3 - 3500 rpm mark hesistating and there is a significant power drop, i was wondering whether resetting the ecu wud help it to re learn the correct air/fuel ratios now that the afm is fixed if this has anything to do with the problem???

please feel free to correct me if i am wrong as im new to this game

Cheers Nick :O

Jmaac Proficient

Jmaac

Posted
Posted

Resetting the ECU lets the computer retune to suit the fuel mixtures your running (depends on fuel & quality/location etc.). Your ECU will do this/reset itself automatically after 50 starts or so anyway...

Jmaac Proficient

Jmaac

Posted
Posted

Occasional backfire could be from a number of things, TPS, atmo BOVS, coolers etc. but firstly look at the timing/tune. Crap fuel shouldnt cause a backfire just a more spontaneous combustion rather than top/down??

The only benefit you'll get from resetting the ecu (apart from resetting other computers) is that the fuel mixtures are more aggressively tuned (i.e. first tune to suit first run), and that benefit will only be realised if you keep using the same blend of fuel i.e. BP Ultimate, Shell Optimax etc. all the time. Ive been told that this occurs dynamically (real time) aswell but it is far less aggressive i.e. tune happens over weeks rather than minutes

Just keep using the same fuel and your ecu will reset itself automatically at some stage. Not sure about the diagram above but the R32 and 33 pinouts are different. Just unplug battery +ve and hit the brake pedal to remove residual - this will also work with most other cars.

An automatic shop tried to charge me 150$ to reset the Auto ECU in a magna doing the same thing, Nissan charge $70 for an ECU reset also, 120$ for a reset & a consult - ridiculous!!

  • 2 years later...
r32man09 Community Regular

r32man09

Posted
Posted

Hey

sorry to start this topic again. I'm about to do a 100,000km service and I would like to reset mystock ecu but I'm not sure what to do as I have a rb20det? Disconecting the battery really work? Can sum1 please explain how reset the ecu on r32?

Cheers

paulr33 Grand Master

paulr33

Posted
Posted

thanks for bumping a 3+ year old thread

to do stock ecu reset undo the battery terminal and press the brake pedal a few times

it will clear out all the power in the system and reset the stock ecu

it will also reset the headunit and other non-nvram based electronics

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...