Jump to content
SAU Community

Resestting ECU

ex-static

By ex-static,
in Engines & Forced Induction

 Share

Recommended Posts

DAMQIK GTS-T Community Regular

DAMQIK GTS-T

Posted
Posted

p.s I dont like getting into the kick pannel were the ecu is as I belive the more one root's arround with it the more likely some of those fine wires will break in the socket.

The less you remove the ecu the better.

Note it would be quite costly to replace the scoket that plugs to the ecu. It could also cause faults that are hard to trace.

Thats why I think its better to reset the ecu the paper clip way.

my 2 cents

DAMQIK

_turtle_ Proficient

_turtle_

Posted
Posted

just tried the paper clip method. it worked!! realised i was putting it in the wrong holes wen DAMQIK said that the points had wires going into them. i was putting the clip into 2 empty ones hehe.

the engine check lite flashed 5 times slow, and then 5 times quick? and then just kept repeating itself after that. anyone know what that means?

  • 2 years later...
R31Heaven Proficient

R31Heaven

Posted
Posted

I know this is digging up an old thread, but I thought the paper clip trick only reset the diagnostics (this needs to be done after replacing a faulty componant) mode not the actual ECU (learning). Droppng power to it and draining off any power by pressing the brake or leaving over night is the only way I know..

  • 3 months later...
  • 3 weeks later...
caz Enthusiast

caz

Posted
Posted

Hey guys, the diagnostic tool you need isnt expensive! and you can share it with any mates that have a pre 97 Nissan with the grey consult diagnostic port. If you have a laptop ,USB ECU Interface cable and software can cost as little as $155.

If you are interested, check out my ad in the 'for sale from our sponsors' .

Im quite happy for you to borrow mine too if you are Sydney based.

Cheers,

Caz... :D

I really don't think it would have done too much.....the proper diagnostic tool is needed and after the reset there are certain driving processes it needs to help the computer 'learn'.

caz Enthusiast

caz

Posted
Posted

CODE 13 is Engine coolant temp sensor, very common fault. Remove and clean the connector with a tiny file and contact cleaner, retension the insides so they connect well, clear the fault from your ecu , replug and try again!

ECU SELF-DIAGNOSTIC ERRORCODES

Code 11* :

Camshaft Angle Sensor circuit (CAS)

Either 1° or 120° signal is not entered for the first few seconds of engine cranking,

Either 1° or 120° signal is not input often enough while the engine speed is higher then the specified RPM.

Check harness and connector (if harness and connector are OK, replace CAS)

Code 12 :

Air Flow Meter circuit (AFM)

The AFM sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector (if harness and connector are OK, replace AFM)

Code 13 :

Engine Coolant Temp. Sensor

The Engine Coolant Temp. Sensor circuit is open or shorted (abnormal voltage is registered).

Check harness and connector of Engine Coolant Temperature sensor

Code 14 :

Speed Sensor circuit

The Speed Sensor circuit is open or shorted.

Check harness and connector speed sensor switch (reed switch)

Code 21*

Ignition signal circuit

The ignition signal in the primary circuit is not entered during engine cranking or running.

Check harness and connector of the Power Transistor Unit

Code 26

Boost Pressure sensor (Turbo models)

The boost pressure sensor is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check for boost pressure leaks, check boost pressure sensor

Code 31

Control Unit

ECU calculation function is failing Replace ECU

Code 32

EGR function

EGR valve does not operate (valve spring does not lift)

Check EGR valve and EGR-solenoid

Code 33

O2 Sensor (left side)

The O2 Sensor is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, O2 sensor, Fuel pressure, Injectors, Intake air leaks

Code 34

Detonation Sensor circuit

The detonation sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check Harness and connector, detonation sensor

Code 35

EGR Temp. Sensor

The EGR Temp. Sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check EGR temp. sensor

Code 42

Fuel Temp Sensor circuit

The Fuel Temp. Sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check Fuel temp. sensor

Code 43

Throttle Position Sensor circuit

The Throttle Position Sensor circuit is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, check throttle position sensor

Code 45

Injector leak

Fuel leaks from the injectors Injectors

Code 51

Injector circuit

The injector circuit is open

Check harness and connector, check injectors

Code 53

O2 Sensor (right side)

The O2 Sensor is open or shorted (abnormally high or low voltage is registered).

Check harness and connector, O2 sensor, fuel pressure, injectors, intake air leaks

Code 54

Signal circuit from the automatic transmission (A/T) (A/T models only)

The A/T communication line is open or shorted

Check harness and connector

Hope this helps,

Cheers, Caz... :D

can someone please post what all the codes are? i cant find it, and me mates has just started flashing code 13.

  • 7 months later...
GTAAAH Mentor

GTAAAH

Posted
Posted (edited)

absurdely old topic and all but, the above list of problems do you need the ecu diagnostic tester to assess? or is there like a LCD screen in the ecu that gives u codes or a LED

thx itd save me asking alot of questions if i could get these codes goin. That and i dont like pulling kick panels apart and going near old wiring if i dont have to

Edited by r32 gts-turbo
  • 1 year later...
  • 2 months later...
Nick033 Experienced

Nick033

Posted
Posted

i know this may seems as a bit of a noob qs but is there any harzards involved with resetting the ecu???

i recently had a faulty afm which i fixed by resoldering the three pins inside on the circuit board, i was getting stalling and hesistation problems all the time and the car chewwed fuel like no tommorow, but the car still seems to run a little rough around the 3 - 3500 rpm mark hesistating and there is a significant power drop, i was wondering whether resetting the ecu wud help it to re learn the correct air/fuel ratios now that the afm is fixed if this has anything to do with the problem???

please feel free to correct me if i am wrong as im new to this game

Cheers Nick :O

Jmaac Proficient

Jmaac

Posted
Posted

Resetting the ECU lets the computer retune to suit the fuel mixtures your running (depends on fuel & quality/location etc.). Your ECU will do this/reset itself automatically after 50 starts or so anyway...

Jmaac Proficient

Jmaac

Posted
Posted

Occasional backfire could be from a number of things, TPS, atmo BOVS, coolers etc. but firstly look at the timing/tune. Crap fuel shouldnt cause a backfire just a more spontaneous combustion rather than top/down??

The only benefit you'll get from resetting the ecu (apart from resetting other computers) is that the fuel mixtures are more aggressively tuned (i.e. first tune to suit first run), and that benefit will only be realised if you keep using the same blend of fuel i.e. BP Ultimate, Shell Optimax etc. all the time. Ive been told that this occurs dynamically (real time) aswell but it is far less aggressive i.e. tune happens over weeks rather than minutes

Just keep using the same fuel and your ecu will reset itself automatically at some stage. Not sure about the diagram above but the R32 and 33 pinouts are different. Just unplug battery +ve and hit the brake pedal to remove residual - this will also work with most other cars.

An automatic shop tried to charge me 150$ to reset the Auto ECU in a magna doing the same thing, Nissan charge $70 for an ECU reset also, 120$ for a reset & a consult - ridiculous!!

  • 2 years later...
r32man09 Community Regular

r32man09

Posted
Posted

Hey

sorry to start this topic again. I'm about to do a 100,000km service and I would like to reset mystock ecu but I'm not sure what to do as I have a rb20det? Disconecting the battery really work? Can sum1 please explain how reset the ecu on r32?

Cheers

paulr33 Grand Master

paulr33

Posted
Posted

thanks for bumping a 3+ year old thread

to do stock ecu reset undo the battery terminal and press the brake pedal a few times

it will clear out all the power in the system and reset the stock ecu

it will also reset the headunit and other non-nvram based electronics

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...