Jump to content
SAU Community

Recommended Posts

Hey Guys i just got this photo of my Car and im in love with it, except the fact that the car was dirty, is it possible that anyone could remove the dirt from my Car and keep it the same good looking picture?? If you can Then i would be very Grateful!!

post-60999-1252937673_thumb.jpg

post-60999-1252937795_thumb.jpg

Edited by Zaver
Link to comment
https://www.sau.com.au/forums/topic/287998-photoshop-the-dirt-off-my-car/
Share on other sites

I haven't contributed to the Computer art section for a while, take a look and let me know what you think of my 30mins work

the file on its own after being re-touched

post-40562-1253079191_thumb.jpg

and a comparison before and after

post-40562-1253079175_thumb.jpg

Hey Turk,

For this job, i created a duplicate layer and hid the original (just so i don't ruin the original in case i need to start over).

I used the Clone stamp tool as opposed to the healing brush, and sampled cleaner areas of the car that had similar color to the area that i was using it on.

I adjusted the Flow down until i got a level that wasn't sampling too much of the other parts of the car, but enough for the darker clean black to show up and just dotted the dirty areas slowly, some more than others.

Once i was done sampling, some of the lines between the panels (ie: skirt to door, front quarter to door) were very difficult to make out, on a new layer i used the brush tool, set to 100% flow, using pure black color and a very fine point(maybe 3px or so but with feathered edges) and drew in the lines for the creases that seemed to have been sampled over or were just hard to see, i then duplicated the layer, changed the lightness of the layer to +100 in the hue and saturation menu to make it white, and moved it one pixel right/left/up or down depending on the direction of the light.

Then just used the eraser on a large size (something like 50px with a feathered edge and flow down around 16% to rub away at the white and black lines i had drawn until they blended in enough to look like the actual lines of the car should.

Finally i merged all of those layers once i was happy with it and duplicated the resulting layer, set the layer style to multiply to bring out the dark tones, decreased the opacity of that layer until i got a nice smooth black that wasn't too dark (just looking at the paint and not the rest of the image).

Then used the eraser again on quite a large size, around 70px or so with a feathered edge, and on 100% flow to remove the majority of the out side of the image leaving just the car (keep in mind the original merged layer is still back there).

And to finish, i decreased the eraser size to a few different sizes using around 30% flow, depending on the area i wanted to erase, and started rubbing the paint sections back where there were reflections, as well as through the window and on the driver, the rims, headlights, tail lights, just anywhere that should be shiny.

And that is is for the most part, i probably made some alterations here and there, i think i added a gradient down the bottom to create the shadow you would see going under the car, but that is the gist of it.

-Steve

Hey Rush, that was actually a really good retouch, I'm guessing you used the healing brush? Mind taking me through how you got it so clean? I tryed to retouch it but had no luck on getting it as clean as you did!
  • 1 month later...
I haven't contributed to the Computer art section for a while, take a look and let me know what you think of my 30mins work

the file on its own after being re-touched

post-40562-1253079191_thumb.jpg

and a comparison before and after

post-40562-1253079175_thumb.jpg

Haha the wonders of photoshop :thumbsup:

And here i was coming into this thread to have a laugh why you wouldnt just clean the car and take more photos. :thumbsup:

They are some good action shots. Some good touch ups as well. Shame im not on my own comp or id have a go as well.

shh, i couldnt b bothered using the pen tool to neaten up those edges, no1 would have noticed if you didnt point it out, damn youuu

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...