Jump to content
SAU Community

Help With Speedo

Curtis.Cow

By Curtis.Cow,
in General Maintenance

 Share

Recommended Posts

rych Contributor

rych

Posted
Posted

same with mine, mine seems to be off by about 20kmph, it only start budging from 0, once i get the speed up to around 20kmph+.

btw, im using a gtr cluster instead for my r33 gtst.If the ecu gets the signal from speedo, not sure if it'll be harmful to the engine on the long run. Been using it for 6 months so far no prob. Friends always teases me wth am i going so slow, i told him my speedo is in MPH lol.

some_cs_student Veteran

some_cs_student

Posted
Posted
same with mine, mine seems to be off by about 20kmph, it only start budging from 0, once i get the speed up to around 20kmph+.

btw, im using a gtr cluster instead for my r33 gtst.If the ecu gets the signal from speedo, not sure if it'll be harmful to the engine on the long run. Been using it for 6 months so far no prob. Friends always teases me wth am i going so slow, i told him my speedo is in MPH lol.

I wrote a thread on how to tweak your speedo by small amounts, there is a MP/H to KM/H conversion too but that might not help you.

There is another tutorial about adjusting your speedo using an electronic calibrator from Jaycar, that may help you...

  • 4 months later...
EVL-R33 Proficient

EVL-R33

Posted
Posted

I got this same problem, my speedo and ODO dont work, but everything else does, so im assuming its my speedo sensor in the gearbox (which im a bout to go down and inspect).

I have an Apexi PFC with hand controller, I used to get accurate speed readings on that before, but the speed readings are on 0 constantly now, so i assume that the speedo sensor (gearbox) gives the cluster (dash) and ECU the readings. In regards to the posts above, I dont think that the ECU gets readings from wheel sensors (on R33s).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...