Jump to content
SAU Community

Oils And Oil Pressure

=STEVE=

By =STEVE=,
in Queensland

 Share

Recommended Posts

=STEVE= Apprentice

=STEVE=

Posted
Posted

hey everyone,

I have only just recently become a 32 owner and already have a few questions if anyone could help.

I've just done an oil change from Royal purple to Motul 4100 turbolight.

They both have the same viscosity range (10w40).

After the change i noticed that my oil pressure is low on idle after driving. Pretty close to zero in fact.

When up in the revs (say 3000 to 4000 revs) the pressure needle doesnt get much higher than 2kg/cm^2

The royal purple that was in it also did the same thing. But the royal purple wasnt very nice to the motor on cold start up, in that i could hear ticking.

So my question..... Is this a normal reading for oil pressure on the RB20??

cheers,

steve

Link to comment
https://www.sau.com.au/forums/topic/289473-oils-and-oil-pressure/
Share on other sites
mosquitocoils Veteran

mosquitocoils

Posted
Posted (edited)

Check the link in my sig

EDIT: Just had another look, doesn't have RB20det in there but you get a good idea from it.

Your pressure seems a bit low, but I'd get a sandwich plate on your oil filter and run an aftermarket oil pressure guage from it before you start freaking out, just in case.

Edited by mosquitocoils
Parag0n Mentor

Parag0n

Posted
Posted
Check the link in my sig

EDIT: Just had another look, doesn't have RB20det in there but you get a good idea from it.

Your pressure seems a bit low, but I'd get a sandwich plate on your oil filter and run an aftermarket oil pressure guage from it before you start freaking out, just in case.

Sandwich plate to the oil filter are terrible.

If you want an accurate reading mount it in the sump.

The Dan Grand Master

The Dan

Posted
Posted

Chances are that the oil pressure is fine. The factory sender is known, and well documented, to be problematic. Get yourself a manual pressure gauge or take it to a mechanic for a pressure test.

Sandwich plate is not necessary as you can just mount it in the same place the factory one goes.

If you want to replace the factory one, they are approx $210 from Nissan.

The Dan Grand Master

The Dan

Posted
Posted
a mobil 1 fully syn product what else ?

Royal Purple R&D their product and and the 10w40 has a higher film strength than Mobil1 also.

None of which has anything to do with his pressure. His brand of oil is not the problem.

32_Dave Mentor

32_Dave

Posted
Posted
Royal Purple R&D their product and and the 10w40 has a higher film strength than Mobil1 also.

None of which has anything to do with his pressure. His brand of oil is not the problem.

i know that, just wanted to see if anyone got protective of an inferior product.

Parag0n Mentor

Parag0n

Posted
Posted
Lol. Are you being serious?

How are you supposed to get an oil pressure reading from the sump?

You're 100 right, I got my pressure and temps mixed up, sorry.

But yes a sandwich plate will be less accurate for TEMPS not pressure, again must of been drunk when i posted that :laugh:

MountainRunner Mentor

MountainRunner

Posted
Posted

A sandwich plate is fine for oil temp as most of them have the end of the sensor in the oil flow, its only a problem when there is no flow over the sensor. Take a look at the data sheet of a typical temp sensor and they are accurate to 5% anyway, this will be the biggest source of inaccuracy unless you calibrate your sensor before installation.

I agree the nissan pressure sensor is very unreliable when old. A new one or aftermarket sensor is the way to go.

Motul oils are the goods. Plenty of track cars run them without any problems. Look at Nissan racing cars and you will usually see Motul stickers on the side.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
A sandwich plate is fine for oil temp as most of them have the end of the sensor in the oil flow, its only a problem when there is no flow over the sensor. Take a look at the data sheet of a typical temp sensor and they are accurate to 5% anyway, this will be the biggest source of inaccuracy unless you calibrate your sensor before installation.

I agree the nissan pressure sensor is very unreliable when old. A new one or aftermarket sensor is the way to go.

Motul oils are the goods. Plenty of track cars run them without any problems. Look at Nissan racing cars and you will usually see Motul stickers on the side.

comes back to the old saying..."if you don't want to spin a bearing...put Motul in it"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • GTSBoy
      Valve clearance for RB25det series 2

      By GTSBoy · Posted

      This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Kinkstaah
      Valve clearance for RB25det series 2

      By Kinkstaah · Posted

      Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • soviet_merlin
      Valve clearance for RB25det series 2

      By soviet_merlin · Posted

      To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • Dose Pipe Sutututu
      Valve clearance for RB25det series 2

      By Dose Pipe Sutututu · Posted

      300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...