Jump to content
SAU Community

Recommended Posts

I have a fresh forged rb25 with a gcg highflow that is run by a wolf 3d that needs a tune, I am located in Adelaide and I want a tuner that has tuned lots of cars with this ECU. I am going to call boost worx tomorrow but I've heard Shaun is more a powerFC, nistune tuner, so if anyone knows any other wolf3D tuners out there that would be great.

Cheers :P

Edited by Rolls
Link to comment
https://www.sau.com.au/forums/topic/289880-best-wolf3d-tuner-in-adelaide/
Share on other sites

I've had mates cars tuned there and they have all left very unhappy, had to go back 2-3x to get the tune right and pay each time, even after that the AFR was still all over the place, you could tell as it would blow black smoke randomly at certain revs.

Rang shaun at boostworx and Im going to get him to tune it, never heard a bad story from him.

Edited by Rolls
Its really hard to find a decent tuner, I reckon I've heard atleast one bad thing about every tuner in Adelaide.

Let us know how you go however :P

True story, boostworx is the only place I haven't heard a bad story about yet so I am going to stick with them I think. Guy seems really honest and nice as well when I've spoken to him before which I think is important, spoken to some apparently good tuners before that just come across as total spanners.

True story, boostworx is the only place I haven't heard a bad story about yet so I am going to stick with them I think. Guy seems really honest and nice as well when I've spoken to him before which I think is important, spoken to some apparently good tuners before that just come across as total spanners.

ahahahhaha i can tell u my BAD story!!!!!!!!!

obviously u havnt spoken to everyone!!!!!!

ahahahhaha i can tell u my BAD story!!!!!!!!!

obviously u havnt spoken to everyone!!!!!!

yer, i got my gtr from a dude who'd had it tuned at boostworx @ 1.2 bar... on stock ceramic turbos

I had it detuned to 1.0 bar as soon as I got it, and have kept it that way since. 1.2 is ok for dyno runs, but its death for ceramics under long load.. 1.1 is pushing it even

As soon as I get my N1's I'll be sorted, they can handle a decent load of boost, but 20 year old ceramic turbos shoud never be ran above 12-14 psi

-D

Even after listening to ovrtym33 story and a few others I'm still going to go to boostworx. Dohmar you never know the previous owner might have asked for a knife edge tune to put a smile on the sellers face?

I'm going to be very direct with what kind of tune I want, nice and lean on cruise for economy and a rich very safe tune for the big revs + boost.

Even after listening to ovrtym33 story and a few others I'm still going to go to boostworx. Dohmar you never know the previous owner might have asked for a knife edge tune to put a smile on the sellers face?

Well I bought the car off Writeoff who is a friend and he was the one that brought the boost issue to my attention. I dont think that's the case at all, esp since I was informed about all issues before I bought the car...

Cronic is right however - youll never find a tuner out there without at least one failed engine - shit sometimes just happens

Weezy 1.2 bar was around 250-260kw and 1.0 bar is around 210-220kw, stock.

-D

Interesting, well I guess as long as I am firm about what I want with him that reliability and a safe tune is far more important than power he will do his best, especially if I offer to pay for an extra hour for him to make sure it is 100%.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...