Jump to content
SAU Community

Recommended Posts

hey guys, on the way home just then i was giving it abit of stick, and then it started making noises and was struggling to reach high rpm so every time i tryed to reach rpm and making a struggling sound...current mod fmic and just got boost controller today, i didnt check the engine bay to look for loose pipping because its too dark. but im paranoid now..any ideas?

Link to comment
https://www.sau.com.au/forums/topic/291327-wierd-noises-help/
Share on other sites

hey guys, on the way home just then i was giving it abit of stick, and then it started making noises and was struggling to reach high rpm so every time i tryed to reach rpm and making a struggling sound...current mod fmic and just got boost controller today, i didnt check the engine bay to look for loose pipping because its too dark. but im paranoid now..any ideas?

struggling sound?????? more info, check ur pipes, boost control hoses, remove controller, start from there, new cooler second hand, new cooler or second hand

just had alook at the engine bay seems fine, no pipes out. yer when i give it to it, it struggles to hit high revs. when i got it in hi boost it does it bad, but when i got it on off mode just a minor bit. wouldnt be coz i got stock ecu?

just had alook at the engine bay seems fine, no pipes out. yer when i give it to it, it struggles to hit high revs. when i got it in hi boost it does it bad, but when i got it on off mode just a minor bit. wouldnt be coz i got stock ecu?

Did you read what I posted? Also, how much boost are you running?

it only happens when i hit high boost, i read a few threads with similar problems and it results in coilpacks, but i dont want to buy them unless im 99% sure :S. by the way if you have faulty coil packs does that mean you get less km's from a tank? because ive been getting less km's recently

question guys, insted of making a new thread i thought id ask here. ive pretty much come to the conclusion my coil packs are on there way out. now im abit short on cash so i was thinking is it worth getting brand new nissan coil packs from justjap or should i save for yellow jackets. would the stock nissan coil packs handle my mods?

take it to a proffesionall

Sighh............ :laugh:

There are a couple wonderful tutorials in the DIY section about fixing coil packs yourself. Lowering the gap is a good idea too (on new plugs). Don't bother spending hundereds of $ until you have exhausted your $free.99 options first. DIY section. Search.

before you go looking at coils, pull your plugs out and see what gap they are and what condition they are in. if they are 1.1mm plugs and have been in there for quite a while they may have worn and the gap may be bigger than 1.1mm so just putting new plugs in will solve the problem and only cost you about $30.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...