Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

ahh ok, cheers for that, hope your right haha, rb20de+t would suck.

wonder why it would have ecr32 written on the ecu then?? hmmmm

also, changed my mind on the turbo AGAIN.

did a dummy fit, i would need to run a spacer on the flange coz the compressor housing hits the manifold

before the studs are tightened, and i need an elbow made up.

i do however need a coolant line, the one that goes from the back of the block to the back of the turbs...

anyone got one lyin round?

looms are similar, ecu's are similar

mine's a ceffy x-over pipe on a 32 engine. its a chop and change part, usually means u need the rubber elbow from the AFM with the extra bits if you want to run the factory bov

So are you saying Cefiro RB20's have no BPV/BOV at all? So they come with hektik flutter from the factory?

from what ive found

unless they've popped their donks in j-land and ended up with a 32 engine haha

from what ive found

unless they've popped their donks in j-land and ended up with a 32 engine haha

far out, I guess that blows the "its put there for a reason" theory

Cefiro crossover pipe here:

http://cgi.ebay.com.au/cefiro-rb20det-cros...=item3ef9e4bb5b

far out, I guess that blows the "its put there for a reason" theory

Cefiro crossover pipe here:

http://cgi.ebay.com.au/cefiro-rb20det-cros...=item3ef9e4bb5b

yeah look exactly like that.....

if it WAS factory na, it would still have to run na ecu right?

wheres dale when ya need him :P

mr hks, judging by the cars that usually have those stickers i thought that stood for Hyundai Kool Skids

u got the wrong car :P o yeah i said that

ive seen that wing b4

post-31501-1257681735_thumb.jpg

lol all good dude, gives it the track look. n i know how u track racers look down on us mountain passers :)

Edited by Inline 6
mr hks, judging by the cars that usually have those stickers i thought that stood for Hyundai Kool Skids

u got the wrong car :) o yeah i said that

ive seen that wing b4

post-31501-1257681735_thumb.jpg

lol all good dude, gives it the track look. n i know how u track racers look down on us mountain passers :)

What you on about?? I dont have any HKS stickers :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you flushed the initial fluid yet? It should look like a rainbow unicorn shat glitter into it. 2nd or 3rd fluid change is when you party.
    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
×
×
  • Create New...