Jump to content
SAU Community

Recommended Posts

Nah got the pump priming. Doesn't even come close to firing up though, just turns over for a bit while draining the shit out of the battery, even when being jumped and the other car is revving a fair bit, it still almost dies completely.

My mate said he could hear the fuel being pumped into the rail, so it might be a spark issue, but I really don't give a fuck anymore. It's time for someone who knows what they're doing re wiring to have a suss (that or it's time to push the cunt over a cliff and gleefully watch the destruction that ensues)

Edited by AndrewJZX100
  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Brand new plates too Mitch :D

o noez haha

Yo Donkey Kong, you should buy my KTS Tie Rod ends - increase steering lock = fully sick hectik driftz :)

sorry peach , if im gonna buy anything for lock it will be drift knuckles

Can you check for spark? Remove one of the coil packs and stick in a spark plug ... crank it over and check for spark? Or timing light if you have one.

:)

I just can't stand to look at the thing at the moment. My mates dad has a multi-meter but none of us who are working on it have a clue about wiring so I guess we've done pretty well to get this far with all the bullshit little differences/problems we've encountered :D

One thing though, Nissan can suck a huge wang. Why the hell would you make every single goddam sensor have a different plug between 2 engines of the same vintage fitted to similar chassis?

UUUGGGHHHH marry me Andrew??

im right there with ya mate, couldnt even get the RB on the engine mounts today,

and Dale needed the crane back ASAP, si i dropped it onto one mount just so its in there

ill take it to a shop and let some other douche deal with it.

between work, My Boy and other duties, i no longer have the time of patience anymore.

FCKING CARS!!!!

gonna do the worlds biggest skid when its done i swear!

UUUGGGHHHH marry me Andrew??

im right there with ya mate, couldnt even get the RB on the engine mounts today,

and Dale needed the crane back ASAP, si i dropped it onto one mount just so its in there

ill take it to a shop and let some other douche deal with it.

between work, My Boy and other duties, i no longer have the time of patience anymore.

FCKING CARS!!!!

gonna do the worlds biggest skid when its done i swear!

LOL we've both come to the same conclusion - some other sucka can deal with it :D

Tandem skids when both our shitboxes are done fo sho.

It wouldn't be so bad if the end result was some bullshit tough motor, but all this shit for a 20? :D

Nah in all honesty mine wouldn'tve been half the headfuck it has if me and my mate didn't make an important decision re how to swap looms while absolutely plastered last weekend :) that was where the real troubles began.

It wouldn't be so bad if the end result was some bullshit tough motor, but all this shit for a 20? :D

Nah in all honesty mine wouldn'tve been half the headf**k it has if me and my mate didn't make an important decision re how to swap looms while absolutely plastered last weekend :) that was where the real troubles began.

try doin it for 8 months for a stock motor haha

Well I think my GTR has proven a new meaning to the term "GTR handle like they're on rails"

Aye thats well low.... what suspension u running? :P

I just got back from a 2 hour drive thru the adelaide hills, from hahndorf to lobethal and gumeracha as well as a few detours here and there, loads of great twisties, some nice sweeping bends and the odd straight road make for a great time. even got to drive on a single lane dirt road with a huge dropoff on one side... gtr lapped it up and asked for seconds

*sigh* so have to do that next weekend

-D

Wonderful! Pulled my RS250 race bike engine down and found some foreign metal in there. :P Appears some douche at the track didn't like a little 250 spanking him and his 1000 and put foreign bits (a piston pin not even for my RS) into my crank case when I left it unattended ... resulting in the clutch basket gear, gearbox engagement gear, and seals being wrecked. Now its rebuild time ... and I haven't started the season! :D

Might have found a race spec motor in Singapore ... waiting for confirmation.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...