Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

just watchin that vid that matty posted again, and noticed the AFM on the strut tower, not even

connected to the intake... how does that work? me want?

it doesnt. had something to do with the regulations specifying that it had to be connected. didnt say it had to be connected and in use though.

Anyone know of a black R34gtr getting around ?

i used to spot one regularly in town during the day craig, led tail lights and big(ger than stock) rims, and if i remember correctly it had personalised plates

havent seen it for a while though, say around 3 months

it doesnt. had something to do with the regulations specifying that it had to be connected. didnt say it had to be connected and in use though.

ahhh ok, i thought it was so you could run a solid pipe to pod without havin AFM in between....

but upon actually thinking about it, it wouldnt work..

Well i had some what of a sucessful day. got the Cressy i bough a few month ago running (just an ignition issue in the end) but then found that the headgasket is stuffed (which i suspected anyway). So if anyone wants an 1993 MX83 Cressy with 178,000km's on the clock with a blown headgasket you can have it for $1300. Or i'll do the gasket myself and put $3000 on it.

Also started pulling parts off the CA to clean them up;

post-27020-1260358124_thumb.jpg

post-27020-1260358415_thumb.jpg

EDIT!!

As for the R32 GTR Vs' R33 GTS-t Brakes they both have the same diameter but the GTR rotors are thicker (32mm V's the GTS-t's 30mm)

Edited by D_Stirls

argh, ive fiddled too much and now the GTR doesnt run smoothly...

ive posted a thread in forced induction, but still:

ive:

removed all the recirculation piping, and blocked off the inlet pipe holes

moved the boost solenoid to a better place

cleaned the AFMs

and put the stock breather hoses and PCV back on, no longer venting gases to atmosphere.

drove fine (with better power steering mind you!) for about 1km, with small amounts of boost,

but now it barely runs, and is stuttering all the time... any ideas what ive done?

where do i start :blink:

Hmm, have you asked if that was okay to use on the AFM's?

I know when I cleaned out AFMs working at sinergy we used Brakecleaner which is a thin liquid that smells really really strongly you can almost taste it and it drys with no moisture left behind.

It has to be the way you plumbed up all the piping etc

Hmm, have you asked if that was okay to use on the AFM's?

I know when I cleaned out AFMs working at sinergy we used Brakecleaner which is a thin liquid that smells really really strongly you can almost taste it and it drys with no moisture left behind.

It has to be the way you plumbed up all the piping etc

i use the stuff at work all day long to clean electronic components

and if it was the pipingm, why would the car run fine for the first half of the trip?

Could have done something and made it over fuel, and now your spark plugs are fvcked hence why it took some time.

Maybe take out your spark plugs and have a look man otherwise I got nfi lol.

Bed time, will check this tomorrow though good luck :).

Could have done something and made it over fuel, and now your spark plugs are fvcked hence why it took some time.

Maybe take out your spark plugs and have a look man otherwise I got nfi lol.

Bed time, will check this tomorrow though good luck :) .

does anyone know if altering the length of the inlet piping after the AFM will alter the way the car runs? or should the tune pick this up and self-correct??

i used to spot one regularly in town during the day craig, led tail lights and big(ger than stock) rims, and if i remember correctly it had personalised plates

havent seen it for a while though, say around 3 months

I know someone who has a R34 Vspec 2 in black ???,, she lives in north adelaide area, dark hair , has a built forged motor in it.

actually she looks a lot like that chick damo...lol, only a model not athlete..lol

asking for a little help

posted in borrow section too..

me 'na mate are rebuilding a suzuki f5a 543cc 3cyl hatch atm, engine is out on ground

cant get the flywheel off, etc.

need to borrow a flywheel stopper holder lock tool

anyone?

a screw driver run thru one of the balance holes is usually enough, if not try a steel scrap through the starter hole ..

if you can get one bolt off, use a steel flat bar and make one,, drill a hole in the end , pop the bolt back into it and use a bellhousing bolt for the other end.. works a treat. WD40 helps too..lol

some take a light heat from a heat gun or plumbers torch to get loose.. but dont overheat the rear main seal or it will melt.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
    • KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
×
×
  • Create New...