Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Ive got a r32 wing to get rid of. 30bux in silver

Rubes - got the actuator ready for you. need to test the larger 18pound unit a bit later

will get it to you next week then.

ordered my 235/45 khumo ku36 tyres

also qfm a1rm 780degree track pads

sorted out front and rear braces, awaiting a seat rail for my seat.

also awaiting 4l surge tank & 305lph external fuel pump. comes with 5m braided fuel line

a cheap chip remap is on its way to me so I'll be piggybacking around the tune until I sort my shite out

trying to sort out the injectors, then will be ready to service and do all fluids.

in will go the roll cage to some extent, do a tune and she'll be ready.

sore-as atm, lol

$15 remap chip, lol

9000rpm, speed cut, boost cut, mapping

lol go ebay, like the $1.25 certified roll cage, $100 yellowjacket coilpacks, etc,

with my mapecu piggyback she should be good.

if not, meh. thought Id try tho.

wiring is all done, was lots and lots of spaghettio's of nothingness

found 2 on/off switches, about 10m of wires connected to nothing

everything is out tho, ready for the cage to go in.

:)

Rubes - got the actuator ready for you. need to test the larger 18pound unit a bit later

will get it to you next week then.

No worries mate. I'm flying out to Sydney on Wednesday, not back until Sunday evening. No rush! :)

Then I got the actuator to fit, new intercooler piping to fit, A custom centre console to finish, and a turbo/boost leak to sort out all in one hit! :)

$15 remap chip, lol

9000rpm, speed cut, boost cut, mapping

lol go ebay, like the $1.25 certified roll cage, $100 yellowjacket coilpacks, etc,

with my mapecu piggyback she should be good.

if not, meh. thought Id try tho.

wiring is all done, was lots and lots of spaghettio's of nothingness

found 2 on/off switches, about 10m of wires connected to nothing

everything is out tho, ready for the cage to go in.

:)

does this mean your not going to buy my power fc??? =\

Does anyone here know of anyone or a place that i looking for night time workers?

Or even anytime after 4pm?

I'm doing full time studies now to get things moving quicker so I can finally be qualified!

Thanks yo!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have a vb in honour of the car comming back
    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
×
×
  • Create New...