Jump to content
SAU Community

Recommended Posts

i have no words to describe the stuff found in this thread...

http://forums.overclockers.com.au/showthread.php?t=860659

im not sure if i should laugh at the stupidity, or be appalled at the sheer amount of bigots....

the whole site is unbelievable

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Hey Chad,

what offsets are you running on your Stagea, and what size tyres. I'm putting on GTSt brakes and need some spacers so I may as well fill the guards out while i'm at it.

The rims I have at the moment are bogan/bob-jane spec +38 18x235s I'm thinking 25-30mm spacers front, maybe 15mm rear or just leave it as they are.

19x8 +30 on the front with 30mm spacers with 235 tyre and they rub on the guards so could do with a 25mm spacer instead. Rear are 19x9 +30 with 235's and they fit sweet.

what are your thoughts on these:

post-18854-1269746395_thumb.jpg

330mm with brackets,

Slotted & Ventilated

Dynamic Balanced

Heat Treated *Surface Coated

Heat resistance up to 900 degree.

$595 on trademe.

or here: http://www.conceptzperformance.com/Cart/de...29118.210.8.101

post-18854-1269746575_thumb.jpg

326mm with brackets, $430usd + postage

also arranging:

hks 87mm pistons & attkd h-beam conrods

acl race main & conrod bearings

ati 600hp harmonic balancer

rb26 clear cam timing cover

apexi multichecker

hks step-2 valve springs

hks oil pump

$3000 delivered. woot. double woot

smilie.gif

I have been reading some of the Landover Baptist stuff Carl .... freaking hilarious ;) .... some of the appalled reactions to what is clearly a joke site are off the dial hilarious. Love this one in particular:

http://www.landoverbaptist.net/showthread.php?t=27676

try not to get cross drilled rotors Brendan they're more likely to crack

My GT-R rotors have tiny little hairline cracks 1 - 2mm long coming from the cross drilled holes,

very shortly I'll be looking for some slotted rotors, along with a brakefluid flush

Edited by Weezy

What happened to race car on a budget brandan? I mean its good if you can get these parts cheap but the costs are going to take you on a roller coaster and before you know it you've spent way more then you had intended lol

it has to be the biggest troll in the history of the internet. the size of the forum is amazing hey

I have been reading some of the Landover Baptist stuff Carl .... freaking hilarious ;) .... some of the appalled reactions to what is clearly a joke site are off the dial hilarious. Love this one in particular:

http://www.landoverbaptist.net/showthread.php?t=27676

What happened to race car on a budget brandan? I mean its good if you can get these parts cheap but the costs are going to take you on a roller coaster and before you know it you've spent way more then you had intended lol

yeh this is for down the track - auto awd rb26 stagea ;)

the sale of parts from the r32 sedan and my current engine will suffice

ie: rb25 ported head, tomei camshafts & valve springs - $2000

rb25 gt3076 garret ball bearing turbo - $1500

rb25 bottom complete bottom end with rwd gtr sump - $500,

rb30 manual box, tein r32 suspension, injectors, splitfires, - $2000

gtr fuel pump, stagea brakes, gtr front calipers, Panoz racing 4-pot billet calipers - $1000

gtst sedan shell, other bits etc, a few more grand easy.

fkn Chinese shit!

took the gate off this arvo, yep, was stuck open, taped it with a hammer, put it back together and back on,

started it up and woooot, i had boost again! gave it a good hard rev after it warmed up, and bah! prick of a thing stayed open.

ahh well, def in the market for a new gate soonish.

<3 the flutterz thru stainless intake pipe tho ;)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...