Jump to content
SAU Community

Recommended Posts

Okay I pulled the hose off with the yellow stripe and I can't feel anything in the hose when I squeeze it. That would tell me that the thing isn't there. But when boosting my standard gauge only goes to the 2nd to last bar on the gauge..

What do we think is going on?

The hose feels pretty stiff as it is, though.

Mines still got the restrictor in it but I pulled out the hose and put a light into it to see the restrictor.

I'm scared if I take it out, bang goes the turbo's lol.

I can't remember what the bars on the gauge actually stand for... like isn't the 2nd bar like 10psi or something?

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

I think the second bar up the top of the gauge is close to 14psi/1bar. Would be great if someone could actually confirm this though. f**ks me what them standard measurements are in

The hose feels pretty stiff as it is, though.

Mines still got the restrictor in it but I pulled out the hose and put a light into it to see the restrictor.

I'm scared if I take it out, bang goes the turbo's lol.

I can't remember what the bars on the gauge actually stand for... like isn't the 2nd bar like 10psi or something?

Which hose is the restrictor in? The bottom or the top?

IMG_7562.jpg

this picture seems to be pointing to the bottom one which is the thicker of the two. But the top one on my car is thinner and has the yellow stripe that everyone says the restrictor is in.

I'm confused. But if its not there and I'm not running 1Bar on my standard guage.. it opens up a whole list of problems I could have..

I think the second bar up the top of the gauge is close to 14psi/1bar. Would be great if someone could actually confirm this though. f**ks me what them standard measurements are in

measurements are in mmHG which is the pressure of mercury - roughly said its the amount of fluid pressure exerted by one mm of mercury, so 760mm of mercury is equal to the sea level atmospheric pressure (1 bar)

http://en.wikipedia.org/wiki/Torr

Scientific measurement, NFI why they put it in a skyline, either bar or psi would have been much better

-D

can i ring aus post to see if its here??

i know it was sent, i just want it my the weekend!!

you'll need a tracking number, like steve said if u got e-parcel u can check it on the web

otherwise give the adelaide cbd post office branch a call, they can possibly tell you if theyve a) recieved it or b) sent it off to a regional office

-D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...