Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

also cant wait for mine.....even though i dont have a car to put them on, they will make a nice wall decoration for the mean time lol

yeah I cant wait till I get my car back. been 4 weeks so far but fingers crossed tomorrow will be the day

had a look at the turbos that came off the gtr (mattyr31 saw them too) and one was rooted...

to quote matty "Hey you can see daylight thru the housing!"

turns out the rear turbine's water feed had become blocked and had most likely overheated and warped the housing, which led to the bearing getting munted and blowing oil into the compressor section - certainly would explain the det and lack of power in either case...

water and oil lines have been thoroughly refurbished now tho, so when it goes to boostworx on monday for a tune i should be pushing some healthy numbers

that aside, its time for a crap joke

Two atoms go into a bar on a Friday night. They are both in a good mood and proceed to drink themselves under the table.

They are now really drunk.

One atom turns to the other in horror and says "Oh Shit, I lost an electron!!"

"My God, are you sure?!" asked the other atom in disbelief.

"Yeah, I'm positive......"

-D

Sorry mate they only bolt onto 34gtr :) 33 is different bolt hole size :( but yes the 6-pot brembo's arrived today. Here I was thinking they were just alittle bigger then the 34R brembo's, but holy shit, they are huge. Bigger then f50. Would basically take up a whole half of a rotor easy.

Pics will be up tomorrow :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...