Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Ive got a r32 wing to get rid of. 30bux in silver

Rubes - got the actuator ready for you. need to test the larger 18pound unit a bit later

will get it to you next week then.

ordered my 235/45 khumo ku36 tyres

also qfm a1rm 780degree track pads

sorted out front and rear braces, awaiting a seat rail for my seat.

also awaiting 4l surge tank & 305lph external fuel pump. comes with 5m braided fuel line

a cheap chip remap is on its way to me so I'll be piggybacking around the tune until I sort my shite out

trying to sort out the injectors, then will be ready to service and do all fluids.

in will go the roll cage to some extent, do a tune and she'll be ready.

sore-as atm, lol

$15 remap chip, lol

9000rpm, speed cut, boost cut, mapping

lol go ebay, like the $1.25 certified roll cage, $100 yellowjacket coilpacks, etc,

with my mapecu piggyback she should be good.

if not, meh. thought Id try tho.

wiring is all done, was lots and lots of spaghettio's of nothingness

found 2 on/off switches, about 10m of wires connected to nothing

everything is out tho, ready for the cage to go in.

:)

Rubes - got the actuator ready for you. need to test the larger 18pound unit a bit later

will get it to you next week then.

No worries mate. I'm flying out to Sydney on Wednesday, not back until Sunday evening. No rush! :)

Then I got the actuator to fit, new intercooler piping to fit, A custom centre console to finish, and a turbo/boost leak to sort out all in one hit! :)

$15 remap chip, lol

9000rpm, speed cut, boost cut, mapping

lol go ebay, like the $1.25 certified roll cage, $100 yellowjacket coilpacks, etc,

with my mapecu piggyback she should be good.

if not, meh. thought Id try tho.

wiring is all done, was lots and lots of spaghettio's of nothingness

found 2 on/off switches, about 10m of wires connected to nothing

everything is out tho, ready for the cage to go in.

:)

does this mean your not going to buy my power fc??? =\

Does anyone here know of anyone or a place that i looking for night time workers?

Or even anytime after 4pm?

I'm doing full time studies now to get things moving quicker so I can finally be qualified!

Thanks yo!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...