Jump to content
SAU Community

Recommended Posts

Today It was my first startup after my single turbo conversion on the gtr.Every thing double checked , I entered the new injector info in the d jetro then when I go to start up ,it starts,then dies after like 2 seconds.If I tap the throttle on and on it will stay on but its struggling,also won't pass 3000rpm...

for the injectors ,correct me if i'm wrong. old size /new size 444/750=0.592 x100 = 59.2% then new latency - old latency [email protected]= 0.01msec

So I entered 59 % for correction and .02 for latency ..cause theres no .01

I also turn off the boost control feedback and 02 sensor feedback.

My map sensors are tee'd of the pcv valve,and the car never ran with the pfc before.

Can someone shed some light on what could be wrong?

I checked your calculations for correct and latency and they're correct (assuming you are sure you have the correct injector size and latency for the new injectors).

I can only think of 2 things, you need to do the idle procedure here: http://paulr33.skylinesaustralia.com/docs/...erfc-faq.htm#21

And the other thing trying a different source to T the map sensor.

PCV valve IS NOT a vacuum / boost source. You need to T off the FPR, or some other hose connected to the plenum.

If that still doesn't solve the problem, you need to adjust fuel &/or timing in the idle area of the maps.

PCV valve IS NOT a vacuum / boost source. You need to T off the FPR, or some other hose connected to the plenum.

If that still doesn't solve the problem, you need to adjust fuel &/or timing in the idle area of the maps.

Alot of people have been runing the map sensors off the pcv valve with great results and others told me to leave the fpr have its own vaccum source .

For the injector size and latency I found the latency on this site http://injector-rehab.com/kbse/lag.htm Siemmens deka 750's = .76 @ 14v.

Edited by gtrdj

Noticed today when I raised the fuel pressure the car stayed on a little longer but not much..Also when I reset the pfc and left it on the stock injector settings it also help staying on longer then the actual new injector settings(stays on for only 5 sec).

did you ever do the base idle adjustment on this PFC? has this PFC ever worked?

when you install a new PFC you need to do the idle adjust and self learn to make sure it idles correctly

this is covered in the PFC FAQ under new installation steps.

if this PFC used to idle in the past check the basics such as fuel, spark and sensors

Yes it has worked on someone elses car,I can't get the car to idle at all,it dies to soon so I wouldn't be able to do the idling self learn.Could it be anything with the Idle control valve?

Edited by gtrdj

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...