Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Guest RedLineGTR

From my experience the pods that make the most "induction noise" are foam based ones...HKS are the loudest imao Trust airinx (yellow mushroom) are behind it... i have also used (have for sale too) the K&N pod filters your get a noise thats not crazy loud but u still get that induction noise..probably reckon would be one of the quiet ones.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-600954
Share on other sites

I have only used and stuck with the K&N pod. It was the first one i bought and had no need to change it.

On the last "skid pan day" people were asking me "what type of bov. do you have, it sounds made!?" I only have the factory plumbed back system, but you can actually here it work through the pod :cheers:.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-601166
Share on other sites

I used to run a Trust Airinix (yellow) pod filter - it was very loud, but IMHO it was very crap at doing what it was supposed to be doing, namely filtering! Took it off to clean it, and holding it up to the light you could clearly see right through it. :cheers:

Call me a pessimist, but if you can see through the filter then the chances are plenty of sh1t can get through and into your engine...:(

I've since ditched it, and replace the stock airbox. OK, it's a lot quieter, but there is no noticeable loss of power and I can rest assured my engine aint breathing in tons of dust and crap on a daily basis..

My 2 yens worth...

But, damn did that Trust pod sound good! :D

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-601324
Share on other sites

shuto is right, those blitz metal sus ones are stoooopidly loud. my mate had one on his r33, and it was so loud, you could hear it sucking hard even just cruising without any load at 100km/h in 5th on the freeway.

hks & trust foam filters would be the 2nd loudest.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-601551
Share on other sites

just got the K&N pod installed, nice sound not too loud but seems ok.

Was wondering since all you guys have a pod, i want to feed in a cold air pipe down there but couldn't seem to find any holes to feed it. I have a stock Intercooler so that pipe running below the pod is in the way. If you have a cold air pipe, where abouts did you guys feed it?

I left the top bit of the stock box so at least can get some air.

Link to comment
https://www.sau.com.au/forums/topic/29367-loudest-pod/#findComment-602185
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...