Jump to content
SAU Community

Recommended Posts

1. R34 GTR, Stock exhaust, cat back (very low k's) , $110

2. R34 GTR/GTT tail lights NEW!! (LED style), $200

2.1 R34 GTT stock light core OEM, $100

2.2 R34 GTT Rear sturd brace , New, $80

3. R33 GTR frond upper Sturd (like new), $50

4. S15 tail lights (like new) , $200

5. HKS pod kit, (SR20DET) (pod it self will fit RB as well), $80

6. JBL GTO Speakers pair, $50

Feel free to PM me for Q>??

post-32314-1256707146_thumb.jpgpost-32314-1256707175_thumb.jpgpost-32314-1256707200_thumb.jpg

Edited by SKYGTT
Link to comment
https://www.sau.com.au/forums/topic/293915-r34-gtr-gtt-parts/
Share on other sites

post-32314-1256727821_thumb.jpg

sorry this is not a light up, would fully look like but very close

it is jsut a camera reflection to give you an idea or what it look like

thanks

Edited by SKYGTT

gee them nismo led rear lights are 2g, thats quite expensive compared to an aftermarket $200 set. i'll be back in oz at the end of month so if you still got them around i'll pick them up

1. R34 GTR, Stock exhaust, cat back (very low k's) ,$90

2. R34 GTR/GTT tail lights NEW!! (LED style), $200

2.1 R34 GTT stock light core OEM, SOLD

2.2 R34 GTT Rear sturd brace , New, SOLD

2.3 R34 GTT OEM Clutch + plate used but still good con. . $50

2.4 R34 GTT 4 OEM shocks. $50

3. R33 GTR frond upper Sturd (like new), $50

4. S15 tail lights (like new) , $200

5. HKS pod kit, (SR20DET) (pod it self will fit RB as well), $80

6. JBL GTO Speakers pair, $50

Feel free to PM me for Q>??

Edited by SKYGTT
  • 3 weeks later...

1. R34 GTR, Stock exhaust, cat back (very low k's) ,$80

2. R34 GTR/GTT tail lights NEW!! (LED look), $200

2.1 R34 GTT stock light core OEM, SOLD

2.2 R34 GTT Rear sturd brace , New, SOLD

2.3 R34 GTT OEM Clutch + plate used but still good con. . $50

2.4 R34 GTT 4 OEM shocks. $50

3. R33 GTR frond upper Sturd (like new), Sold

4. S15 tail lights (like new) , $200

5. HKS pod kit, (SR20DET) (pod it self will fit RB as well), $80

6. JBL GTO Speakers pair, $50

7. R34 GTT Front sway bar,

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...