Jump to content
SAU Community

Recommended Posts

the problem: less coolent in radiator after drive,I need top up everytime when engine is cool(about 250ml sometime more sometime less). the coolent in overflow bottle is getting more and more. so thats mean: coolent flow to overflow bottle when hot, but when cool down the coolent not fully go back to radiator. i did some record. the coolent still go in to radiator when cold but not as much as the coolent from radiator to overflow bottle when hot. say coolent from radiator to overflow bottle 500ml when hot, when its cool down the coolent only come back to radiator 250ml.

I went to a few place to check the cooling system. all good. no problem at all. all of them suggest me try to change a cap.

then I bought a new radiator cap(1.3bar), nothing changed.

but my car never overheat always 75-85degree on PFC. can i just drive like this? don't need really care about it??? I worried the coolent in radiator will getting less and less during time.

I got arc radiator and nismo cap.

car is r34gtr.

anyone help please!!!

the fact that if isn't drawing coolant back into the radiator suggests there is something wrong. if you have a new cap, then i would be looking at the overflow bottle or the hose to the overflow bottle. there may be a small amount of debris at the bottom of the overflow bottle that is allowing the coolant to come in, but when it tries to suck it back in it is blocking up the hole and not letting it back in.

If it's not the cap then it is likely the tube running form radiator overflow or quite possibly the nipple on the radiator. My thoughts are that the force of fluid coming out of the radiator when hot is high but the force under vacuum for refilling when cold is low. The hole might have corroded or the hose is partially blocked.

The hole in my aluminium radiator was blocked from a little bit of crap, I just scraped it out with a drill bit.

First thing to do is to look for coolant stain's over your engine block, top of gearbox at rear, around hoses ect, my next thing would be respective of head gasket or turbo seals.

its still about 150ml coolent less in radiator. the coolent should be full in radiator no matter engine burn water or not is that right?? if the engine burn water the coolent in overflow bottle should getting lower not the coolent in radiator?

PS: I have nismo water pump

Edited by Nosure
if the motor is using coolant it will use it from the radiator first then the overflow.

either you have a small leak which is only evident under pressure or you have a headgasket issue.

even the engine using some coolant does the radiator should still full? and the overflow should get less coolant?

the radiator should always be full. The overflow bottle is an expansion chamber basically when the coolant is hot, it expands and some is pushed to the overflow bottle and then taken back into the radiator once cool.

what you need to do, is fill the rad with bleed screw on the manifold taken out til the system is full. then reseal the system, make sure the overflow bottle is filled to the MAX line and then mark it.

drive for a few days and then re check it.

if you have lost coolant from either the rad or the overflow then you either have a leak or a gasket problem, simple as that

better way to bleed system. leave your cap and cock on the top of your manifold off, run the car up to op temp and let all air in the system bleed out thoroughly.

making sure your overflow is half full?

the radiator should always be full. The overflow bottle is an expansion chamber basically when the coolant is hot, it expands and some is pushed to the overflow bottle and then taken back into the radiator once cool.

what you need to do, is fill the rad with bleed screw on the manifold taken out til the system is full. then reseal the system, make sure the overflow bottle is filled to the MAX line and then mark it.

drive for a few days and then re check it.

if you have lost coolant from either the rad or the overflow then you either have a leak or a gasket problem, simple as that

thanks mate but where is the bleed screw?? and how can I do it?? some more detail please

better way to bleed system. leave your cap and cock on the top of your manifold off, run the car up to op temp and let all air in the system bleed out thoroughly.

making sure your overflow is half full?

OK I will try it. thanks mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...