Jump to content
SAU Community

Recommended Posts

Ok so here is my story.

Started my car, sound system was on low volume. Started driving and put up the volume and noticed the speakers where cracking/distorting, had no clue what could be wrong since everything was fine the day before.

Checked my amps, nothing seemed out of ordinary, checked setting on the head unit and everything was the same. Pulled out the head unit to find one of my RCA's where broken..no brainer here, I found the problem right? Went out to buy new RCA leads, plugged them straight in and it continued to make the same distortion.

So now it gets tricky and I ask myself is it my amp? I called my mate over and we plugged the RCA's into his amps so his speakers would be getting the signals from my head unit. Distortion continues to through his speakers. Now it has to be the head unit sending out crappy signals? I plugged in a whole new deck and the distortions still continued!

Sound systems can really do your head in sometimes lol but yes any help would be appreciated!

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/295427-help-with-wierd-distortion/
Share on other sites

try to plug a ipod or something into the RCA instead of your radio as a source unit on your car ? does it still do it ?

no or yes ?

No , prob a rooted radio , or shorted wire on Radio to ground if one of the speaker wires is hitting ground the resistance skyrockets and the preamp cant deal with the load and distorts bad.

try wiggling the radio around on low volume, does it do it still ? crackle ? spark ?

Yes

then the amp or signal RCA is stuffed , RCA pinched under seat bolts is common

what brand of radio is it ?

your not using a factory high power to RCA converter are you ?

The amp is a Soundstream Lil Wonder, so its new and it is a pretty good amp. The radio is a Sony Xplod unit, it is pretty old but I also put in a Pioneer deck which caused the same sounds.

I will give the ipod a go and see what happens.

Thanks for the suggestions guys.

what about interference with elec.. in the wires.. if you've ruled out amp.. speakers.. headunit.. i would be looking into the wires you've run through the car

^

all good points I think , but your description of speaker noises doesnt lend itself to electrical interference ?

cracking and distorting, is normally only on 1 or 2 speakers , when they get punched in/torn or burned coils, etc.(or if you carry crap in your door pockets that rattles)

if all of them do it , its in the signal path

if its more a whine or crackle then its in the RCA ,power/ground path most of the time

if it does it with the car off as well as on then you know its not the charging system , unless the battery is shithouse below 12volts

Soundstream Lil wonders fail, as does any amp

Sony radios fail same as above

you have ruled out the radio already so check the amp power and signal cables ? check the speaker wires on the amp, are they cross shorted on the terminals or pinched under or thru anything ?

who installed it a Pro or self ? have you installed or seviced anything else on the car since it started ?

if all else fails

GO SEE A PRO IN PERSON,, hard to see or hear what kind of issues you have beyond the forum and what was suggested already, hope that helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...