Jump to content
SAU Community

R34 Rebuilt N1 Gtr Turbos.

Angus Smart
 Share

Recommended Posts

Angus Smart Grand Master

Angus Smart

Posted
Posted

Got a set of gtr turbos that came off my 32..

they were originally R34 N1's which i had rebuild while changing dumps a few years ago.

the center cartridge was changed as garrett had no stock at the time, they were given a larger front wheel +5mm and the same rear.

they are now similar to a gt-rs turbo but with the r34n1 rear exhaust housing. so this eliminates the lag people complain about with gt-rs

they are very responsive and a very good combo. no problems with them at all. i just need the money for a holiday in feb.

they would have gone back on my car when i get the engine back but Heli skiing in Alaska is calling my name! @ 1000usd a day..

$2200 ono they would have under 5000km's on them engine went pop on cyl #6

will get some photos up shortly ;)

Link to comment
https://www.sau.com.au/forums/topic/296433-r34-rebuilt-n1-gtr-turbos/
Share on other sites
Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted

Never had it dynoed after the turbos went on..

but there was alot. i was running about 1.6 bar would have a stab and say in the ranges of 500-550hp

it would pull very hard from around 2900-9000 car also had small bolt in cams

Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted

I've had a word to my friend who drives lots of high powered cars, tunes them etc..

before turbos rebuilt i had 398hp at the wheels.

after we did the dumps and turbos he said there would have been a very responsive 500hp with alot more left in it.

i need to dig out boxes tonite to get photos since these were going back on my car i had them packed away with all my other bits and pieces.

Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted

Center part number is

446179-5031

And for the photos.

post-31456-1258524450_thumb.jpgpost-31456-1258524473_thumb.jpg

post-31456-1258524494_thumb.jpgpost-31456-1258524512_thumb.jpg

post-31456-1258524528_thumb.jpg

I'd even buy these back if you haven't put them on by mid march :)

Neg on price make me an offer! need em gone asap! heliskiing is calling!!

Angus Smart Grand Master

Angus Smart

Posted
  • Author
Posted

Still for sale!

$2000 firm for turbos that have well less than 5000km on them! i'd say more around 2000km as i didnt drive it that much.

Posted via courier anywhere in Australia!

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...