Jump to content
SAU Community

Recommended Posts

hey guys

I have recently been ripped off by a con mechanic..this mechanic runs a so called "performance shop" at *** in sydney named as ***...when i visited him with my skyline R34 which had missfire problem..he said "it was a computer problem" he made me get a microtech ecu for the car..and later on he said "the car needs new spark plugs and coil pack"..he recommended "nissan factory coil pack" instead of "split fire coil pack"..but the car was still missfiring even after the coilpack replacement..and then said the motor was blown off..and changed the cylinder heads..which was an expensive affair too...like this he sucked thousands of dollars from me..but the car was still causing the same problem..later i went to another mechanic who checked and found that ..a couple of coil springs were missing..replaced the spark plugs that were set up for too rich application...tuned up the car and its running nice and well now...so i would like to caution all of our friends about *** at petersham...so please do not go there with ur car...the mechanic over there which i can not name is an absolutly dishonest man..who is running a rip-off business ...plz beware of such mechanics...anyway wish u all enjoy ur driving experience..bye now...

*edit by mods * forum rules do not permit you to name businesses in negative threads. you are welcome to privately pm the name to people if you wish but do not publicly post

Link to comment
https://www.sau.com.au/forums/topic/296712-getting-ripped-off-by-the-mechanic/
Share on other sites

Ouch!!

I know a tuner/mechanic up here that does it too. Every car getting tuned has this fabled ''fuel problem'' $3000 later and the engine fails.

I know how frustrating it can be

idiots like this give mechanics a bad name.. its a terrible act... but one that is replayed over and over again.. driving the good mechanics broke because everyone learns how to do their own work after a dodgy incident like this.

Never go to a mechanic that isn't recommended by a group of people (like on this forum) for such repairs. Why he thought it would be the ECU is beyond me. Going to a spares place and replacing with same ECU would have ruled that out and you may have been able to return the ECU if it didn't fix the problem.

And I forgot to add.. learn to fix your car yourself.

????? Not everyone can fix cars themselves, hence why he went somewhere to get the car fixed.

If i used that line to most of my clients "learn to fix your computer yourself" ( I.T Manager) i would never have any work.

Just some food for thought

Hmmmm,

This reminds me of how in the 70s & 80s, that if you were scammed by someone, you could hire...

1) a group of people in the debt collection industry to picket a place until they went out of business or compensated you

2) an individual who was specially dressed in bag-man clothes with stinky overcoat and sit in the waiting lounge till...

Methinks that repentance is more constructive than reprisal :)

Ouch!!

I know a tuner/mechanic up here that does it too. Every car getting tuned has this fabled ''fuel problem'' $3000 later and the engine fails.

I know how frustrating it can be

yes mate..i think u r talking about the same bastard who ripped me off...coz he made me spend $3000 for the computer..

no mate..i wish i could..u semm to live in sydney..could u recommend a good mechanic for me plz..

Several...

Guys at Unigroup Engineering > Girraween 96312470

Garry at Just Jap > Kirrawee 95450532

Alistair at Powerplay Imports > Drummoyne 98197555

Guys at Hills Motorsports > Castle Hill 98999962

And unfortunately not all shops recommended on this forum are honest either. I had one recommended on here [and people are still using him and getting ripped off] that had the hide to change thousands for a dump pipe and tune and I mean thousands. Then tried to rip me off even more with second hand goods and telling me my new stuff was faulty - what a joke.

If I could I'd name him every time cos he's still doing it now........but he has his regular mates who say how good he is and propping him up - and he probably helps them out OK.

The mods gave me the same treatment.

What I'd like to do is post up my account and the total and say what work was not done and what work was poorly/not done as I had asked [i gave them a typed sheet of instructions] - not judge the business but let others do that.

It would not be a negative thread then....................but I'd only get kicked by the mods again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...