Jump to content
SAU Community

Recommended Posts

hey guys

I have recently been ripped off by a con mechanic..this mechanic runs a so called "performance shop" at *** in sydney named as ***...when i visited him with my skyline R34 which had missfire problem..he said "it was a computer problem" he made me get a microtech ecu for the car..and later on he said "the car needs new spark plugs and coil pack"..he recommended "nissan factory coil pack" instead of "split fire coil pack"..but the car was still missfiring even after the coilpack replacement..and then said the motor was blown off..and changed the cylinder heads..which was an expensive affair too...like this he sucked thousands of dollars from me..but the car was still causing the same problem..later i went to another mechanic who checked and found that ..a couple of coil springs were missing..replaced the spark plugs that were set up for too rich application...tuned up the car and its running nice and well now...so i would like to caution all of our friends about *** at petersham...so please do not go there with ur car...the mechanic over there which i can not name is an absolutly dishonest man..who is running a rip-off business ...plz beware of such mechanics...anyway wish u all enjoy ur driving experience..bye now...

*edit by mods * forum rules do not permit you to name businesses in negative threads. you are welcome to privately pm the name to people if you wish but do not publicly post

Link to comment
https://www.sau.com.au/forums/topic/296712-getting-ripped-off-by-the-mechanic/
Share on other sites

Ouch!!

I know a tuner/mechanic up here that does it too. Every car getting tuned has this fabled ''fuel problem'' $3000 later and the engine fails.

I know how frustrating it can be

idiots like this give mechanics a bad name.. its a terrible act... but one that is replayed over and over again.. driving the good mechanics broke because everyone learns how to do their own work after a dodgy incident like this.

Never go to a mechanic that isn't recommended by a group of people (like on this forum) for such repairs. Why he thought it would be the ECU is beyond me. Going to a spares place and replacing with same ECU would have ruled that out and you may have been able to return the ECU if it didn't fix the problem.

And I forgot to add.. learn to fix your car yourself.

????? Not everyone can fix cars themselves, hence why he went somewhere to get the car fixed.

If i used that line to most of my clients "learn to fix your computer yourself" ( I.T Manager) i would never have any work.

Just some food for thought

Hmmmm,

This reminds me of how in the 70s & 80s, that if you were scammed by someone, you could hire...

1) a group of people in the debt collection industry to picket a place until they went out of business or compensated you

2) an individual who was specially dressed in bag-man clothes with stinky overcoat and sit in the waiting lounge till...

Methinks that repentance is more constructive than reprisal :)

Ouch!!

I know a tuner/mechanic up here that does it too. Every car getting tuned has this fabled ''fuel problem'' $3000 later and the engine fails.

I know how frustrating it can be

yes mate..i think u r talking about the same bastard who ripped me off...coz he made me spend $3000 for the computer..

no mate..i wish i could..u semm to live in sydney..could u recommend a good mechanic for me plz..

Several...

Guys at Unigroup Engineering > Girraween 96312470

Garry at Just Jap > Kirrawee 95450532

Alistair at Powerplay Imports > Drummoyne 98197555

Guys at Hills Motorsports > Castle Hill 98999962

And unfortunately not all shops recommended on this forum are honest either. I had one recommended on here [and people are still using him and getting ripped off] that had the hide to change thousands for a dump pipe and tune and I mean thousands. Then tried to rip me off even more with second hand goods and telling me my new stuff was faulty - what a joke.

If I could I'd name him every time cos he's still doing it now........but he has his regular mates who say how good he is and propping him up - and he probably helps them out OK.

The mods gave me the same treatment.

What I'd like to do is post up my account and the total and say what work was not done and what work was poorly/not done as I had asked [i gave them a typed sheet of instructions] - not judge the business but let others do that.

It would not be a negative thread then....................but I'd only get kicked by the mods again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...